Search Advanced

AIMS Materials Science

2020, Volume 7, Issue 6: 859-870. doi: 10.3934/matersci.2020.6.859
Previous Article Next Article
Review

Review on properties of hybrid aluminum–ceramics/fly ash composites

  • 1.
    Department of Materials and Metallurgical Engineering, Federal University Oye-Ekiti, Ekiti State, Nigeria
  • 2.
    Department of Chemistry, Federal University Oye-Ekiti, Ekiti State, Nigeria
  • 3.
    Department of Mechanical Engineering, Alex Ekwueme Federal University, Ndufu-Alike, Ikwo, Ebonyi State, Nigeria
  • 4.
    Department of Polymer Technology, Nigerian Institute of Leather and Science Technology, Zaria, Kaduna State, Nigeria
  • 5.
    Department of Metallurgical and Materials Engineering, Federal University of Technology Akure, Ondo State, Nigeria
  • Received: 04 September 2020 Accepted: 03 December 2020 Published: 07 December 2020

  • The production and characterization of metal matrix composites reinforced with fly ash is a very active research area. This paper presents a review on the properties of hybrid aluminum–SiC/fly ash, hybrid aluminum–B4C/fly ash, hybrid aluminum–Al2O3/fly ash, hybrid aluminum–graphite/fly ash and hybrid aluminum–BN/fly ash composites. The major production route utilized by the various authors was stir casting technique and its variant; powder metallurgy was also utilized by few authors. Improved mechanical properties were observed in the hybrid composites, compared to the composites filled with single reinforcements. It was observed that the properties of the composites were influenced by both the volume fractions of the reinforcements in the matrix and the percentage of replacement of the ceramic reinforcements with fly ash in the hybrid reinforcement mixture. In most of the reports, beyond 40 wt% of replacement of ceramic reinforcements by fly ash, the wear resistance, strength and ductility of the hybrid composites excessively reduced (high brittle tendency), while corrosion tendency increased. Generally, the mechanical properties and wear resistance of the hybrid composites were reported to increase with increase in weight fractions of the reinforcement in the composites until about 15 wt%, beyond which the properties depreciate. At the right ratio of the reinforcements in the hybrid mixture and up to about 15 wt% weight fractions of reinforcements in the composites, the reinforcements were reported to distribute uniformly in the matrix. The major observation was that most of the reports focused on the mechanical properties and wear behavior. Reports are lacking on the thermal and electrical properties of hybrid aluminum–ceramics/fly ash composites. Other areas such as hybrid TiC/fly ash composites are yet to be explored.

    Citation: Reginald Umunakwe, Ifeoma Janefrances Umunakwe, Uzoma Samuel Nwigwe, Wilson Uzochukwu Eze, Akinlabi Oyetunji. Review on properties of hybrid aluminum–ceramics/fly ash composites[J]. AIMS Materials Science, 2020, 7(6): 859-870. doi: 10.3934/matersci.2020.6.859

    Related Papers:

  • The production and characterization of metal matrix composites reinforced with fly ash is a very active research area. This paper presents a review on the properties of hybrid aluminum–SiC/fly ash, hybrid aluminum–B4C/fly ash, hybrid aluminum–Al2O3/fly ash, hybrid aluminum–graphite/fly ash and hybrid aluminum–BN/fly ash composites. The major production route utilized by the various authors was stir casting technique and its variant; powder metallurgy was also utilized by few authors. Improved mechanical properties were observed in the hybrid composites, compared to the composites filled with single reinforcements. It was observed that the properties of the composites were influenced by both the volume fractions of the reinforcements in the matrix and the percentage of replacement of the ceramic reinforcements with fly ash in the hybrid reinforcement mixture. In most of the reports, beyond 40 wt% of replacement of ceramic reinforcements by fly ash, the wear resistance, strength and ductility of the hybrid composites excessively reduced (high brittle tendency), while corrosion tendency increased. Generally, the mechanical properties and wear resistance of the hybrid composites were reported to increase with increase in weight fractions of the reinforcement in the composites until about 15 wt%, beyond which the properties depreciate. At the right ratio of the reinforcements in the hybrid mixture and up to about 15 wt% weight fractions of reinforcements in the composites, the reinforcements were reported to distribute uniformly in the matrix. The major observation was that most of the reports focused on the mechanical properties and wear behavior. Reports are lacking on the thermal and electrical properties of hybrid aluminum–ceramics/fly ash composites. Other areas such as hybrid TiC/fly ash composites are yet to be explored.


    加载中


    [1] Tang HG, Ma XF, Zhoa W, et al. (2007) The mechanical properties of magnesium matrix composites reinforced with 10 wt% W14Al86 alloy particles. J Alloy Compd 437: 285–288.
    [2] Lee DG, Kim HS, Kim JW, et al. (2004) Design and manufacture of an automotive hybrid aluminum/composite drive shaft. Compos Struct 67: 87–99.
    [3] Dey A, Pandey KM (2016) Characterization of fly ash and its reinforcement effect on metal matrix composites: a review. Rev Adv Mater Sci 44: 168–181.
    [4] Senapati AK, Mishra PC, Routara BC (2014) Use of waste flyash in fabrication of aluminium alloy matrix composite. Int J Eng Technol 6 : 905–912.
    [5] Umunakwe R, Olaleye DJ, Oyetunji A, et al. (2017) Assessment of some mechanical properties and microstructure of particulate periwinkle shell–aluminium 6063 metal matrix composite (PPS-ALMMC) produced by two-step casting. Niger J Technol 36: 421–427.
    [6] Umunakwe R, Okoye OC, Nwigwe US, et al. (2017). Effects of stirring time and particles preheating on porosity, mechanical properties and microstructure of periwinkle shell–aluminium metal matrix composite (PPS-ALMMC). Ann Fac Eng Hunedoara 15: 133–140.
    [7] Shanmughasundaram P, Subramanian R, Prabhu G (2011) Some studies on aluminium—fly ash composites fabricated by two step stir casting method. Eur J Sci Res 68: 204–218.
    [8] Kondaiah VV, Panthangi RK, Rao KS (2018) Microstructure and mechanical properties of flyash particle reinforced aluminum composite. Int J Mech Eng Technol 9: 893–897.
    [9] Razzaq MA, Majid DL, Ishak MR, et al. (2017) Effect of fly ash addition on the physical and mechanical properties of AA6063 alloy reinforcement. Metals 7: 477–492.
    [10] Kulkarni SG, Meghnani JV, Lal A (2014) Effect of fly ash hybrid reinforcement on mechanical property and density of aluminium 356 alloy. Procedia Mater Sci 5: 746–754.
    [11] Boopathi MM, Arulshri KP, Iyandurai N (2013) Evaluation of mechanical properties of aluminium alloy 2024 reinforced with silicon carbide and fly ash hybrid metal matrix composites. Am J Appl Sci 10: 219–229.
    [12] Jimenez AF, Palomo A (2003) Characterisation of fly ashes: potential reactivity as alkaline cements. Fuel 82: 2259–2265.
    [13] Dwivedi SP, Sharma S, Mishra RK (2014) Microstructure and mechanical behavior of A356/SiC/fly-ash hybrid composites produced by electromagnetic stir casting. J Braz Soc Mech Sci Eng 37: 57–67.
    [14] Kosmatka SH, Wilson ML (2011) Fly ash, slag, silica fume, and natural pozzolans, Design and Control of Concrete Mixtures, 15 Eds., Illinois: Portland Cement Association, 57–72.
    [15] Sahu MK, Sahu RK (2020) Experimental investigation, modeling, and optimization of wear parameters of B4C and fly-ash reinforced aluminum hybrid composite. Front Phys 8: 1–14.
    [16] Kanth UR, Rao PS, Krishna MG (2019) Mechanical behavior of fly ash/SiC particles reinforced Al–Zn alloy-based metal matrix composites fabricated by stir casting method. J Mater Res Technol 8: 737–744.
    [17] Mahendra KV, Radhakrishna K (2010).Characterization of stir cast AlCu(fly ash + SiC) hybrid metal matrix composites. J Compos Mater 44: 989–1005.
    [18] Boopathi MM, Arulshri KM, Iyandurai N, et al. (2014) Dry sliding wear, co-efficient of friction and corrosion behaviour of aluminium alloy 2024 reinforced with silicon carbide and fly ash hybrid metal matrix composites. Int J Mech Mechatron Eng 14: 44–53.
    [19] Maga VK, Motagi BS (2014) A study on mechanical properties of aluminium alloy (lm6) reinforced with fly ash, red mud and silicon carbide. IOSR-JMCE 11: 7–16.
    [20] Kumar BR, Thiagarajan M, Chandrasekaran K (2016) Investigation of mechanical and wear properties of LM24/silicate/fly ash hybrid composite using vortex technique. Adv Mater Sci Eng 2016: 1–8.
    [21] Adeosun SO, Osoba LO, Taiwo OO (2014) Characteristics of aluminum hybrid composites. Int Scholar Sci Res Innov 6: 692–699.
    [22] Selvam DR, Smart DS, Dinaharan I (2015) Synthesis and characterization of Al6061–Fly Ashp–SiCp composites by stir casting and compocasting methods. Energy Procedia 34: 637–646.
    [23] Sathishkumar N, Pravinkumar S, Prabhu BA, et al. (2020) Investigation of mechanical properties in Al359 hybrid metal matrix composite reinforced with SiC and fly ash. Mater Today Proc In press.
    [24] Bodunri MO, Alaneme KK, Chown LH (2015) Aluminium matrix hybrid composites: a review of the reinforcement philosophies, mechanical, corrosion and tribological characteristics. J Mater Res Technol 4: 434–445.
    [25] Muthukumar S, Mariappan R (2016) Microstructure characterization of aa6061 alloy/silicon carbide/fly ash hybrid metal matrix composite produced by powder metallurgy route. ARPN J Eng Appl Sci 11: 14545–14551.
    [26] Reddy BR, Srinivas C (2018). Fabrication and characterization of silicon carbide and fly ash reinforced aluminium metal matrix hybrid composites. Mater Today Proc 5: 8374–8381.
    [27] Gireesh CH, Prasad KG, Ramji K (2018) Experimental investigation on mechanical properties of an Al6061 hybrid metal matrix composite. J Compos Sci 2: 49–58.
    [28] Shaikh MB (2018) A statistical analysis of wear behaviour of fly ash reinforced Al–SiC hybrid composites. J Powder Metall Min 7: 190–194.
    [29] Santhosh N, Kempaiah UN, Gowda AC, et al. (2017) Corrosion characterization of silicon carbide and fly ash particulates dispersion strengthened aluminium 5083 composites. J Catal Catal 4: 9–21.
    [30] Arunachalam S, Chelladurai SJ (2020) Optimization of dry sliding wear parameters of AA336 aluminum alloy-boron carbide and fly ash reinforced hybrid composites by stir casting process. Materwiss Werksttech 51: 189–198.
    [31] Canute X, Majumder MC (2018). Mechanical and tribological behaviour of stir cast aluminium/boron carbide/fly ash composites. Int J Eng Sci Technol 13: 755–777.
    [32] Chelladurai SJ, Murugesan T, Rajamani T, et al. (2019) Investigation on mechanical properties and tribological behaviour of stir cast LM13 aluminium alloy based particulate hybrid composites. Materwiss Werksttech 50: 864–874.
    [33] Sahu MK, Sahu RK (2020). Synthesis, microstructure and hardness of Al 7075/B4C/fly-ash composite using stir casting. Mater Today Proc 27: 2401–2406.
    [34] Reddy TP, Kishore SJ, Theja PC, et al. (2020) Development and wear behavior investigation on aluminum-7075/B4C/fly ash metal matrix composites. Adv Compos Hybrid Mater 3: 255–265.
    [35] Babu KA, Venkataramaiah P, Dhama RK (2018). Mechanical characterization of aluminium hybrid metal matrix composites synthesized by using stir casting process. Mater Today Proc 5: 28155–28163.
    [36] Natarajan N, Moorthy AA, Sivakumar R, et al. (2012) Dry sliding wear and mechanical behavior of aluminium/fly ash/graphite hybrid metal matrix composite using taguchi method. IJMER 4: 1224–1230.
    [37] Prasat VS, Subramanian R (2013) Tribological properties of AlSi10Mg/fly ash/graphite hybrid metal matrix composites. Ind Lubr Tribol 65 : 399–409.
    [38] Moorthy AA, Eswaran P, Subramaniyan M (2018) Investigation on dry sliding wear behaviour of self-lubricating metal matrix composites reinforced with fly ash and solid lubricant. Int J Recent Technol Eng 7: 413–416.
    [39] Moorthy AA, Natarajan N, Palani PK, et al. (2013) Study on tribological characteristics of self-lubricating aa2218–fly ash–white graphite composites. Int J Eng Technol 5: 4193–4198.
  • Reader Comments
  • © 2020 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索
AIMS Materials Science
1.8 4.2

Metrics

Article views(2118) PDF downloads(225) Cited by(1)

Preview PDF
Download XML
Export Citation
Article outline

Figures and Tables

Tables(4)

Other Articles By Authors

Related pages

Tools

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog