Numerous research studies have been conducted to enhance fuel economy and reduce emissions by converting diesel engines to run on aqueous ammonia-diesel (AAD) blends. However, only a few studies have investigated the effect of the piston bowl geometry on combustion efficiency and emissions from AAD blends. This study investigated the effect of piston bowl geometry on the combustion efficiency of a diesel engine fueled with AAD blends. Five different types of piston bowls, namely the Double lip (Case 1), 10D100 (Case 2), Mexican hat (Case 3), Inveco F1C Rollbuch (Case 4), and Peugeot DW 10 (Case 5), were used. Diesel-RK software was used for modeling and simulating the fuel combustion inside the diesel engine. Based on the numerical findings, with the same combustion chamber, the results show that the NOx emission, smoke level, and peak pressure reduced with increased engine speed from 2000 to 3000 rpm, whereas peak temperature, CO2, and PM emissions increased. Moreover, among all designs, Case 5 achieved the highest combustion performance, with peak pressure and temperature, along with the lowest PM and smoke. However, it produced the highest NOx emissions. In contrast, Case 1 yielded the lowest NOx, peak pressure, and temperature, but the highest PM, indicating poor combustion. Case 3 achieves the second-highest peak pressure (53.13 bar at 2000 rpm and 52.61 bar at 3000 rpm) and second-highest temperature (1886.8 K at 2000 rpm and 1914 K at 3000 rpm), and only moderately elevated NOx. Case 3 offers the best overall emission balance while maintaining high combustion efficiency, making it the most suitable piston bowl geometry for sustainable operation with AAD blends.
Citation: Hussein A. Mahmood, Osam H. Attia, Ali O. Al-Sulttani. Numerical study of the impact of piston bowl geometry on emissions and combustion properties in diesel engine fueled with aqueous ammonia and diesel mixture[J]. AIMS Energy, 2026, 14(3): 618-639. doi: 10.3934/energy.2026026
Numerous research studies have been conducted to enhance fuel economy and reduce emissions by converting diesel engines to run on aqueous ammonia-diesel (AAD) blends. However, only a few studies have investigated the effect of the piston bowl geometry on combustion efficiency and emissions from AAD blends. This study investigated the effect of piston bowl geometry on the combustion efficiency of a diesel engine fueled with AAD blends. Five different types of piston bowls, namely the Double lip (Case 1), 10D100 (Case 2), Mexican hat (Case 3), Inveco F1C Rollbuch (Case 4), and Peugeot DW 10 (Case 5), were used. Diesel-RK software was used for modeling and simulating the fuel combustion inside the diesel engine. Based on the numerical findings, with the same combustion chamber, the results show that the NOx emission, smoke level, and peak pressure reduced with increased engine speed from 2000 to 3000 rpm, whereas peak temperature, CO2, and PM emissions increased. Moreover, among all designs, Case 5 achieved the highest combustion performance, with peak pressure and temperature, along with the lowest PM and smoke. However, it produced the highest NOx emissions. In contrast, Case 1 yielded the lowest NOx, peak pressure, and temperature, but the highest PM, indicating poor combustion. Case 3 achieves the second-highest peak pressure (53.13 bar at 2000 rpm and 52.61 bar at 3000 rpm) and second-highest temperature (1886.8 K at 2000 rpm and 1914 K at 3000 rpm), and only moderately elevated NOx. Case 3 offers the best overall emission balance while maintaining high combustion efficiency, making it the most suitable piston bowl geometry for sustainable operation with AAD blends.
| [1] |
Sehili Y, Loubar K, Tarabet L, et al. (2024) Computational investigation of the influence of combustion chamber characteristics on a heavy-duty ammonia diesel dual fuel engine. Energies 17: 1231. https://doi.org/10.3390/en17051231 doi: 10.3390/en17051231
|
| [2] |
Naife TM (2022) Improvement of diesel fuel engine performance by nanoparticles additives. J Eng 28: 77–90. https://doi.org/10.31026/j.eng.2022.04.06 doi: 10.31026/j.eng.2022.04.06
|
| [3] |
Ghareeb HO, Anjal HAAW (2024) Ignition delay period prediction for compression ignition engines fueled with ethanol/diesel blends. J Eng 30: 48–70. https://doi.org/10.31026/j.eng.2024.08.04 doi: 10.31026/j.eng.2024.08.04
|
| [4] |
Mahmood HA, Al-Sulttani AO, Mousa NA, et al. (2022) Impact of lambda value on combustion characteristics and emissions of syngas-diesel dual-fuel engine. Int J Technol 13: 179–189. https://doi.org/10.14716/ijtech.v13i1.5060 doi: 10.14716/ijtech.v13i1.5060
|
| [5] |
Mahmood HA, Al-Sulttani AO, Attia OH (2021) Simulation of syngas addition effect on emissions characteristics, combustion, and performance of the diesel engine working under dual fuel mode and lambda value of 1.6. IOP Conf Ser: Earth Environ Sci 779: 012116. https://doi.org/10.1088/1755-1315/779/1/012116 doi: 10.1088/1755-1315/779/1/012116
|
| [6] |
Chaichan MT (2011) Exhaust analysis and performance of a single cylinder diesel engine run on dual fuels mode. J Eng 17: 873–885. https://doi.org/10.31026/j.eng.2011.04.17 doi: 10.31026/j.eng.2011.04.17
|
| [7] | Mahmood HA, Adam NM, Sahari BB, et al. (2016) Investigation on the air-gas characteristics of air-gas mixer designed for bi-engines. Int J Appl Eng Res 11: 7786–7794. |
| [8] |
Luo W, Liu H, Liu L, et al. (2023) Effects of scavenging port angle and combustion chamber geometry on combustion and emmission of a high-pressure direct-injection natural gas marine engine. Int J Green Energy 20: 616–628. https://doi.org/10.1080/15435075.2022.2079380 doi: 10.1080/15435075.2022.2079380
|
| [9] |
Telaumbanua IK, Imai K, Sasaki K, et al. (2024) A pathway for implementing ammonia solutions as fuel blends for achieving low-emission combustion in diesel engines. J Energy Inst 116: 101750. https://doi.org/10.1016/j.joei.2024.101750 doi: 10.1016/j.joei.2024.101750
|
| [10] |
Ali, Lim O (2024) Numerical investigation of combustion and emission characteristics of the single-cylinder diesel engine fueled with diesel-ammonia mixture. Energies 17: 5782. https://doi.org/10.3390/en17225782 doi: 10.3390/en17225782
|
| [11] |
Chaichan MT, Abaas KI, Mohammed BA (2017) Experimental study of the effect of fuel type on the emitted emissions from SIE at idle period. Al-Khwarizmi Eng J 13: 1–12. https://doi.org/10.22153/kej.2017.11.001 doi: 10.22153/kej.2017.11.001
|
| [12] |
Abdollahi M, Ghobadian B, Najafi G, et al. (2020) Impact of water–biodiesel–diesel nano-emulsion fuel on performance parameters and diesel engine emission. Fuel 280: 118576. https://doi.org/10.1016/j.fuel.2020.118576 doi: 10.1016/j.fuel.2020.118576
|
| [13] |
Mahmood HA, Al-Sulttani AO, Attia OH (2025) Numerical investigations of SiO2 and TiO2 nanoparticle's addition impact on performance, combustion features, and emission characteristics of a diesel engine operating with water diesel emulsified fuel at different lambda values and engine speeds. Int J Technol 16: 1731–1751. https://doi.org/10.14716/ijtech.v16i5.7685 doi: 10.14716/ijtech.v16i5.7685
|
| [14] |
Oliveira P, Brójo F (2024) An experimental study on the performance and emissions of an 8% water-in-diesel emulsion stabilized by a hydrophilic surfactant blend. Energies 17: 1328. https://doi.org/10.3390/en17061328 doi: 10.3390/en17061328
|
| [15] |
Hasannuddin AK, Wira JY, Sarah S, et al. (2016) Performance, emissions and lubricant oil analysis of diesel engine running on emulsion fuel. Energy Convers Manage 117: 548–557. https://doi.org/10.1016/j.enconman.2016.03.057 doi: 10.1016/j.enconman.2016.03.057
|
| [16] |
Watanabe S, Yahya WJ, Ithnin AM, et al. (2017) Performance and emissions of diesel engine fuelled with water-in-diesel emulsion. JSAEM 1: 12–19. https://doi.org/10.56381/jsaem.v1i1.3 doi: 10.56381/jsaem.v1i1.3
|
| [17] |
Berwal P, Kumar S, Khandelwal B (2021) A comprehensive review on synthesis, chemical kinetics, and practical application of ammonia as future fuel for combustion. J Energy Inst 99: 273–298. https://doi.org/10.1016/j.joei.2021.10.001 doi: 10.1016/j.joei.2021.10.001
|
| [18] |
Xiao H, Ying W, Chen A, et al. (2024) Study on the impact of ammonia–diesel dual-fuel combustion on performance of a medium-speed diesel engine. J Mar Sci Eng 12: 806. https://doi.org/10.3390/jmse12050806 doi: 10.3390/jmse12050806
|
| [19] |
Guo L, Zhu J, Fu L, et al. (2023) Effects of pre-injection strategy on combustion characteristics of ammonia/diesel dual-fuel compression ignition mode. Energies 16: 7687. https://doi.org/10.3390/en16237687 doi: 10.3390/en16237687
|
| [20] |
Mikulčić H, Baleta J, Wang X, et al. (2021) Numerical simulation of ammonia/methane/air combustion using reduced chemical kinetics models. Int J Hydrogen Energy 46: 23548–23563. https://doi.org/10.1016/j.ijhydene.2021.01.109 doi: 10.1016/j.ijhydene.2021.01.109
|
| [21] |
Zhao Z, Miao X, Chen X, et al. (2024) Simulation study of diesel spray tilt angle and ammonia energy ratio effect on ammonia-diesel dual-fuel engine performance. Energy Eng 121: 2603–2620. https://doi.org/10.32604/ee.2024.051237 doi: 10.32604/ee.2024.051237
|
| [22] |
Frankl S, Gleis S, Karmann S, et al. (2021) Investigation of ammonia and hydrogen as CO2-free fuels for heavy duty engines using a high pressure dual fuel combustion process. Int J Engine Res 22: 3196–3208. https://doi.org/10.1177/146808742096787 doi: 10.1177/146808742096787
|
| [23] |
Zhang Z, Long W, Dong P, et al. (2023) Performance characteristics of a two-stroke low speed engine applying ammonia/diesel dual direct injection strategy. Fuel 332: 126086. https://doi.org/10.1016/j.fuel.2022.126086 doi: 10.1016/j.fuel.2022.126086
|
| [24] |
Zhang H, Wang J (2015) Ammonia coverage ratio and input simultaneous estimation in ground vehicle selective catalytic reduction (SCR) systems. J Frankl Inst 352: 708–723. https://doi.org/10.1016/j.jfranklin.2014.06.009 doi: 10.1016/j.jfranklin.2014.06.009
|
| [25] |
Scharl V, Sattelmayer T (2024) Spectroscopic investigation of diesel-piloted ammonia spray combustion. Fuel 358: 130201. https://doi.org/10.1016/j.fuel.2023.130201 doi: 10.1016/j.fuel.2023.130201
|
| [26] |
Scharl V, Sattelmayer T (2022) Ignition and combustion characteristics of diesel piloted ammonia injections. Fuel Commun 11: 100068. https://doi.org/10.1016/j.jfueco.2022.100068 doi: 10.1016/j.jfueco.2022.100068
|
| [27] |
Nadimi E, Przybyła G, Lewandowski MT, et al. (2023) Effects of ammonia on combustion, emissions, and performance of the ammonia/diesel dual-fuel compression ignition engine. J Energy Inst 107: 101158. https://doi.org/10.1016/j.joei.2022.101158 doi: 10.1016/j.joei.2022.101158
|
| [28] |
Reiter AJ, Kong SC (2011) Combustion and emissions characteristics of compression-ignition engine using dual ammonia-diesel fuel. Fuel 90: 87–97. https://doi.org/10.1016/j.fuel.2010.07.055 doi: 10.1016/j.fuel.2010.07.055
|
| [29] |
Huang Q, Yang R, Liu J, et al. (2025) CFD-based numerical investigation of ammonia combustion and slip characteristics in an ammonia-diesel dual-fuel engine. J Energy Inst 122: 102217. https://doi.org/10.1016/j.joei.2025.102217 doi: 10.1016/j.joei.2025.102217
|
| [30] |
Frost J, Tall A, Sheriff AM, et al. (2021) An experimental and modelling study of dual fuel aqueous ammonia and diesel combustion in a single cylinder compression ignition engine. Int J Hydrogen Energy 46: 35495–35510. https://doi.org/10.1016/j.ijhydene.2021.08.089 doi: 10.1016/j.ijhydene.2021.08.089
|
| [31] |
Al-Dawody MF, Al-Obaidi W, Aboud ED, et al. (2023) Mechanical engineering advantages of a dual fuel diesel engine powered by diesel and aqueous ammonia blends. Fuel 346: 128398. https://doi.org/10.1016/j.fuel.2023.128398 doi: 10.1016/j.fuel.2023.128398
|
| [32] |
Pyrc M, Gruca M, Jamrozik A, et al. (2021) An experimental investigation of the performance, emission and combustion stability of compression ignition engine powered by diesel and ammonia solution (NH4OH). Int J Engine Res 22: 2639–2653. https://doi.org/10.1177/1468087420940942 doi: 10.1177/1468087420940942
|
| [33] |
Sarıtaş M, Kül VS, Akansu SO, et al. (2025) Compression ignition engine performance and emissions: An experimental study on the impact of aqueous ammonia, hydrogen, and diesel fuel blends. Int J Hydrogen Energy 137: 679–688. https://doi.org/10.1016/j.ijhydene.2025.05.121 doi: 10.1016/j.ijhydene.2025.05.121
|
| [34] |
Deresso H, Nallamothu RB, Ancha VR, et al. (2022) Numerical study of different shape design of piston bowl for diesel engine combustion in a light duty single-cylinder engine. Heliyon 8: e09602. https://doi.org/10.1016/j.heliyon.2022.e09602 doi: 10.1016/j.heliyon.2022.e09602
|
| [35] |
Rizvi IH, Gupta R (2021) Numerical investigation of injection parameters and piston bowl geometries on emission and thermal performance of DI diesel engine. SN Appl Sci 3: 626. https://doi.org/10.1007/s42452-021-04633-1 doi: 10.1007/s42452-021-04633-1
|
| [36] | Al Rifat A, Rahman MM, Rahman MA (2026) Effect of piston bowl geometry on combustion, performance, and emission characteristics of a dual-fuel engine. Future Energy 5: 1–9. Available from: https://fupubco.com/fuen/article/view/556. |
| [37] |
Sefatjoo H, Khaleghi H (2026) Influence of piston bowl geometry and swirl ratio on spray dynamics and fuel–air mixing in compression ignition diesel engines. Appl Therm Eng 289: 129908. https://doi.org/10.1016/j.applthermaleng.2026.129908 doi: 10.1016/j.applthermaleng.2026.129908
|
| [38] | Siddique SA, Vijaya K, Reddy K (2015) Theoretical investigation on combustion chamber geometry of DI diesel engine to improve the performance by using Diesel-RK. Int J Innov Technol Explor Eng 4: 27–31. Available from: https://www.ijitee.org/wp-content/uploads/papers/v4i10/J19980341015.pdf. |
| [39] |
Venu H, Soudagar MEM, Kiong TS, et al. (2025) Nanotechnology and LSTM machine learning algorithms in advanced fuel spray dynamics in CI engines with different bowl geometries. Sci Rep 15: 983. https://doi.org/10.1038/s41598-024-83211-y doi: 10.1038/s41598-024-83211-y
|
| [40] |
Pham VC, Kim JK, Lee W-J, et al. (2022) Effects of piston bowl geometry on combustion and emissions of a four-stroke heavy-duty diesel marine engine. Appl Sci 12: 13012. https://doi.org/10.3390/app122413012 doi: 10.3390/app122413012
|
| [41] |
Abdelrazek MK, Abdelaal MM, El-Nahas AM (2022) Piston bowl shape and biodiesel fuel effects on combustion and emission of diesel engines. J Eng Appl Sci 69: 103. https://doi.org/10.1186/s44147-022-00158-5 doi: 10.1186/s44147-022-00158-5
|
| [42] |
Mahmood HA, Al-Sulttani AO, Alrazen HA, et al. (2024) The impact of different compression ratios on emissions, and combustion characteristics of a biodiesel engine. AIMS Energy 12: 924–945. https://doi.org/10.3934/energy.2024043 doi: 10.3934/energy.2024043
|
| [43] |
Adib AR, Rahman MM, Hassan T, et al. (2024) Novel biofuel blends for diesel engines: optimizing engine performance and emissions with C. cohnii microalgae biodiesel and algae-derived renewable diesel blends. Energy Convers Manage: X 23: 100688. https://doi.org/10.1016/j.ecmx.2024.100688 doi: 10.1016/j.ecmx.2024.100688
|
| [44] |
Rehman M, Kesharvani S, Dwivedi G (2023) Numerical investigation of performance, combustion, and emission characteristics of various microalgae biodiesel on CI engine. Fuels 4: 132–155. https://doi.org/10.3390/fuels4020009 doi: 10.3390/fuels4020009
|
| [45] |
Mohsen MJ, Al-Dawody MF (2022) The combustion characteristics of compression ignition engine fuelled partially by LPG-Diesel blends (Simulation study). Al-Qadisiyah J Eng Sci 15: 156–163. https://doi.org/10.30772/qjes.v15i3.828 doi: 10.30772/qjes.v15i3.828
|
Figures(17) / Tables(4)
Hussein A. Mahmood, Osam H. Attia, Ali O. Al-Sulttani. Numerical study of the impact of piston bowl geometry on emissions and combustion properties in diesel engine fueled with aqueous ammonia and diesel mixture[J]. AIMS Energy, 2026, 14(3): 618-639. doi: 10.3934/energy.2026026
DownLoad: