Citation: Falko Böttger-Hiller, Klaus Nestler, Henning Zeidler, Gunther Glowa, Thomas Lampke. Plasma electrolytic polishing of metalized carbon fibers[J]. AIMS Materials Science, 2016, 3(1): 260-269. doi: 10.3934/matersci.2016.1.260
[1] | Barlas TK, van Kuik GAM (2010) Review of state of the art in smart rotor control research for wind turbines. Prog Aerosp Sci 46: 1–27. |
[2] |
Cattafesta LN, Sheplak M (2011) Actuators for Active Flow Control. Annu Rev Fluid Mech 43: 247–272. doi: 10.1146/annurev-fluid-122109-160634
![]() |
[3] |
Böttger-Hiller F, Neumann S, Fehrmann F, et al. (2014) Nickel-plated carbon fiber fabrics for solderable carbon fiber-reinforced plastics with a permeation barrier. Mat-wiss u Werkstofftech 45: 546–551. doi: 10.1002/mawe.201400261
![]() |
[4] | Forke R, Scheibner D, Hiller K, et al. (2008) Fabrication and characterization of a force coupled sensor–actuator system for adjustable resonant low frequency vibration detection. Sensor Actuat A Phys 145–146: 245–256. |
[5] | Mäder T (2015) Neuartige Sensoren zur Erfassung von Dehnungen in Faserkunsttoffverbundwerkstoffen (Structural Health Monitoring). Dissertation, TU Chemnitz. |
[6] |
Böttger-Hiller F, Jahn P, Lindner T, et al. (2015) Electrically conductive carbon-fiber-reinforced plastics (CFRP) with accessible functional layer. Mat-wiss u Werkstofftech 46: 844–851. doi: 10.1002/mawe.201500439
![]() |
[7] | Böttger-Hiller F, Nier M, Lampke T (2014) Metal Coated Carbon Fibres for Multifunctional CFRPs. Int Surfe Technol 1: 44–45. |
[8] | Nier M, Böttger T, Böttger-Hiller F, et al. (2013) Metalized carbon fibers for solderable and wear-resistant composite materials. ICCM 19: 5820–5827. |
[9] |
Njuhovic E, Witt A, Kempf W, et al. (2013) Influence of the composite surface structure on the peel strength of metallized carbon fibre-reinforced epoxy. Surf Coating Technol 232: 319–325. doi: 10.1016/j.surfcoat.2013.05.025
![]() |
[10] | Kupferinstitut D (1999) Löten von Kupfer und Kupferlegierungen. DKI-Inforationsdruck 06: 4–5. |
[11] |
Parfenov EV, Yerokhin A, Nevyantseva RR, et al. (2015) Towards smart electrolytic plasma technologies: An overview of methodological approaches to process modeling. Surf Coating Technol 269: 2–22. doi: 10.1016/j.surfcoat.2015.02.019
![]() |
[12] |
Nevyantseva RR, Gorbatkov SA, Parfenov EV, et al. (2001) The influence of vapor–gaseous envelope behavior on plasma electrolytic coating removal. Surf Coating Technol 148: 30–37. doi: 10.1016/S0257-8972(01)01334-2
![]() |
[13] | Beck U, Lange R, Neumann H-G (2007) Micro- and nanoscaled titanium surface structures textured by electrolytic plasma and etching methods. Adv Mater Res 15: 141–146. |
[14] |
Yerokhin A, Pilkington A, Matthews A (2010) Pulse current plasma electrolytic cleaning of AISI 4340 steel. J Mater Process Tech 210: 54–63. doi: 10.1016/j.jmatprotec.2009.08.018
![]() |
[15] | Nestler K, Böttger-Hiller F, Adamitzki W, et al. (2016) Plasma Electrolytic Polishing–an Overview of Applied Technologies and Current Challenges to Extend the Polishable Material Range. Procedia CIRP, [accepted]. |
[16] | Zeidler H, Boettger-Hiller F, Edelmann J, et al. (2015) Surface finish machining of medical parts using Plasma electrolytic Polishing. Procedia CIRP, doi 10.1016/j.procir.2015.07.038. |
[17] |
Hoche H, Groß S, Foerster R, et al. (2009) Development of Decorative and Corrosion Resistant Coatings for the Surface Refinement of Magnesium Alloys by Plasma-based Methods. Plasma Process Polym 6: 671–677. doi: 10.1002/ppap.200931708
![]() |
[18] | Nestler K, Böttger-Hiller F, Adamitzki W, et al. (2015) Plasma-elektrolytisches Polieren von Kupfer und dessen Legierungen. Galvanotechnik, [submitted]. |
[19] | Duradzhi VN, Bryantsev IV, Tokarov AK (1979) Investigation of erosion of the anode under the action of an electrolytic plasma on it. Elektronnaya Obrabotka Materialov 5: 15–19. |