Research article Special Issues

Reliability-based EDM process parameter optimization using kriging model and sequential sampling

  • Received: 24 June 2019 Accepted: 08 August 2019 Published: 14 August 2019
  • Electrical discharge machining (EDM) is an effective method to process micro-hole for electrically conductive materials regardless of the hardness. However, the machining accuracy and cost are greatly affected by EDM parameters, which are of slight fluctuations in actual machining process. In view of this, reliability-based design optimization (RBDO) method is introduced to balance the electrode wear and aperture gap when unavoidable uncertainties are considered. Kriging model trained by inherited Latin hypercube design (ILHD) and expected feasibility function with objective function (OEFF) criterion is applied to model the influences of peak current, pulse on time and pulse off time on electrode wear and aperture gap. By calling the Kriging model, the probability and corresponding gradient of aperture gap less than the requirement are calculated using Monte Carlo simulation (MCS) and the EDM process parameters are optimized using sequential approximation programming (SAP) algorithm. Using the optimal EDM parameters to perform verification experiments, the feasibility of proposed method is demonstrated, where smaller electrode wear as low as 174.2 μm is obtained with the reliability satisfaction (β = 3.02) of aperture gap.

    Citation: Ma Jun, Han Xinyu, Xu Qian, Chen Shiyou, Zhao Wenbo, Li Xiaoke. Reliability-based EDM process parameter optimization using kriging model and sequential sampling[J]. Mathematical Biosciences and Engineering, 2019, 16(6): 7421-7432. doi: 10.3934/mbe.2019371

    Related Papers:

  • Electrical discharge machining (EDM) is an effective method to process micro-hole for electrically conductive materials regardless of the hardness. However, the machining accuracy and cost are greatly affected by EDM parameters, which are of slight fluctuations in actual machining process. In view of this, reliability-based design optimization (RBDO) method is introduced to balance the electrode wear and aperture gap when unavoidable uncertainties are considered. Kriging model trained by inherited Latin hypercube design (ILHD) and expected feasibility function with objective function (OEFF) criterion is applied to model the influences of peak current, pulse on time and pulse off time on electrode wear and aperture gap. By calling the Kriging model, the probability and corresponding gradient of aperture gap less than the requirement are calculated using Monte Carlo simulation (MCS) and the EDM process parameters are optimized using sequential approximation programming (SAP) algorithm. Using the optimal EDM parameters to perform verification experiments, the feasibility of proposed method is demonstrated, where smaller electrode wear as low as 174.2 μm is obtained with the reliability satisfaction (β = 3.02) of aperture gap.


    加载中


    [1] R. Ramakrishnan and L. Karunamoorthy, Multi response optimization of wire EDM operations using robust design of experiments, Int. J. Adv. Manuf. Tech., 29 (2006), 105–112.
    [2] A. Mandal, A. R. Dixit, S. Chattopadhyaya, et al., Improvement of surface integrity of Nimonic C 263 super alloy produced by WEDM through various post processing techniques, Int. J. Adv. Manuf. Tech., 93 (2017), 433–443.
    [3] G. Rajyalakshmi and P. V. Ramaiah, Multiple process parameter optimization of wire electrical discharge machining on inconel 825 using taguchi grey relational analysis, Int. J. Adv. Manuf. Tech., 69 (2013), 1249–1262.
    [4] S. Gopalakannan, T. Senthilvelan, S. Ranganathan, et al., Modeling and optimization of EDM process parameters on machining of Al 7075-B4C MMC using RSM, Procedia Eng., 38 (2012), 685–690.
    [5] A. Majumder, Process parameter optimization during EDM of AISI 316 LN stainless steel by using fuzzy based multi-objective PSO, J. Mech. Sci. Tech., 27 (2013), 2143–2151.
    [6] A. Nikalje, A. Kumar and K. Srinadh, Influence of parameters and optimization of EDM performance measures on MDN 300 steel using taguchi method, Int. J. Adv. Manuf. Tech., 69 (2013), 41–49.
    [7] L. Zhang, Z. Jia, F. Wang, et al., A hybrid model using supporting vector machine and multi-objective genetic algorithm for processing parameters optimization in micro-EDM, Int. J. Adv. Manuf. Tech., 51 (2010), 575–586.
    [8] H. Lee and C. Liu, Optimizing the EDM hole-drilling strain gage method for the measurement of residual stress, J. Mater. Process. Tech., 209 (2009), 5626–5635.
    [9] T. A. El-Taweel, Multi-response optimization of EDM with Al–Cu–Si–Tic P/M composite electrode, Int. J. Adv. Manuf. Tech., 44 (2009), 100–113.
    [10] X. Li, F. Yan, J. Ma, et al., RBF and NSGA-II based EDM process parameters optimization with multiple constraints, Math. Biosci. Eng., 16 (5) (2019), 5788–5803.
    [11] X. Li, L. Gao, Q. Pan, et al., An effective hybrid genetic algorithm and variable neighborhood search for integrated process planning and scheduling in a packaging machine workshop, IEEE T. Syst. Man. Cy. S., (2018), 1–13.
    [12] Y. Lin, Y. Chen, D. Wang, et al., Optimization of machining parameters in magnetic force assisted EDM based on Taguchi method, J. Mater. Process. Tech., 209 (2009), 3374–3383.
    [13] Z. Chen, H. Qiu, L. Gao, et al., An optimal shifting vector approach for efficient probabilistic design, Struct. Multidiscip. O., 47 (2013), 905–920.
    [14] X. Li, H. Qiu, Z. Chen, et al., A local kriging approximation method using MPP for reliability-based design optimization, Comput. Struct., 162 (2016), 102–115.
    [15] X. Li, H. Qiu, Z. Chen, et al., A local sampling method with variable radius for RBDO using Kriging, Eng. Comput., 32 (2015), 1908–1933.
    [16] A. Chiralaksanakul and S. Mahadevan, First-order approximation methods in reliability-based design optimization, J. Mech. Design, 127 (2005), 851–857.
    [17] B. Keshtegar and M. Zeng, A hybrid relaxed first-order reliability method for efficient structural reliability analysis, Struct. Saf., 66 (2017), 84–93. 18. G. Bird, Monte-carlo simulation in an engineering context, Prog. Astronaut. Aeronaut., 74 (1981), 239–255.
    [18] 19. S. Au and J. L. Beck, A new adaptive importance sampling scheme for reliability calculations, Struct. Saf., 21 (1999), 135–158.
    [19] 20. C. Jiang, H. Qiu, X. Li, et al., Iterative reliable design space approach for efficient reliability-based design optimization. Eng. Comput., (20, 1–19.
    [20] 21. D. Lehký, O. Slowik and D. Novák, Reliability-based design: Artificial neural networks and double-loop reliability-based optimization approaches, Adv. Eng. Softw., 117 (8): 123–135.
    [21] 22. C. Jiang, H. Qiu, L. Gao, et al., An adaptive hybrid single-loop method for reliability-based design optimization using iterative control strategy, Struct. Multidiscip. O., 56 (2017), 1271–1286.
    [22] 23. X. Du, Saddlepoint approximation for sequential optimization and reliability analysis, J. Mech. Design, 130 (2008), 011011.
    [23] 24. P. Zhang, P. Breitkopf, C. Vayssade, et al., XU-RSM: Diffuse Response surface model for reliability-based design optimization, IOP conference series: Materials Science and Engineering, 10 (2010), 012209.
    [24] 25. A. Basudhar and S. Missoum, A sampling-based approach for probabilistic design with random fields, Comput. Meth. Appl. Mech. Eng., 198 (2009), 3647–3655.
    [25] 26. G. Li and Z. Meng, Reliability-based design optimization with the RBF neural network model, Appl. Math. Mech. 35 (2014), 1271–1279.
    [26] 27. N. Xiao, M. Zuo and C. Zhou, A new adaptive sequential sampling method to construct surrogate models for efficient reliability analysis, Reliab. Eng. Syst. Saf., 169 (2018), 330–338.
    [27] 28. C. Jiang, H. Qiu, L. Gao, et al., Real-time estimation error-guided active learning Kriging method for time-dependent reliability analysis, Appl. Math. Model., 77 (2020), 82–98.
    [28] 29. B. Echard, N. Gayton and M. Lemaire, AK-MCS: An active learning reliability method combining kriging and monte carlo simulation, Struct. Saf., 33 (2011), 145–154.
    [29] 30. C. Jiang, H. Qiu, Z. Yang, et al., A general failure-pursuing sampling framework for surrogate-based reliability analysis, Reliab. Eng. Syst. Saf., 183 (2019), 47–59.
    [30] 31. B. J. Bichon, M. S. Eldred, L. P. Swiler, et al., Efficient global reliability analysis for nonlinear implicit performance functions, AIAA J., 46 (2008), 2459–2468.
    [31] 32. W. C. Yeh, J. C. P. Su, T. J. Hsieh, et al., Approximate reliability function based on wavelet latin hypercube sampling and bee recurrent neural network, IEEE T. Reliab., 60 (2011), 404–414.
    [32] 33. G. Wang, Adaptive response surface method using inherited latin hypercube design points, transactions-american society of mechanical engineers, J. Mech. Design, 125 (2003), 210–220.
    [33] 34. X. Li, J. Du, Z. Chen, et al., Reliability-based NC milling parameters optimization using ensemble metamodel. Int. J. Adv. Manuf. Tech., 97 (2018), 9–3369.
    [34] 35. Z. Jia, F. Gu, F. Wang, et al., Parameter optimization of EDM micro-and-small holes based on signal-to-noise and grey relational grade, Chin. J. Mech. Eng., 43 (2007), 63–67.
  • Reader Comments
  • © 2019 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索

Metrics

Article views(3245) PDF downloads(426) Cited by(4)

Article outline

Figures and Tables

Figures(2)  /  Tables(5)

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog