Review Special Issues

Surface protection of Mg alloys in automotive applications: A review

  • Received: 15 February 2019 Accepted: 04 May 2019 Published: 04 July 2019
  • Mg alloys find widespread applications in transportation industries especially in cars and trucks because of their edges in light-weight design, which can greatly help improve the fuel efficiency and decrease the gas emissions of vehicles; However, Mg alloys’ high sensitivity to the corrosive environments limit their penetration in automotive applications. Surface coating is one of the most effective and economic ways to protect Mg alloys from corrosion. Presently, the currently researched and commercial coatings that are specifically applied to Mg alloys in the automotive industry are reviewed in this paper. With some Mg automotive components subjected to corrosion and repeated load simultaneously, corrosion fatigue of coated Mg alloys are reviewed as well. Additionally, a part of attention in this review is given to the assessment approaches of corrosion and corrosion fatigue performance of coated Mg alloys for the purpose of material/surface coating system selection. Finally, some corrosion-related challenges for the growth of Mg alloys, future developments and research directions on surface coatings and corrosion fatigue testing approaches are discussed.

    Citation: Jie Wang, Xin Pang, Hamid Jahed. Surface protection of Mg alloys in automotive applications: A review[J]. AIMS Materials Science, 2019, 6(4): 567-600. doi: 10.3934/matersci.2019.4.567

    Related Papers:

  • Mg alloys find widespread applications in transportation industries especially in cars and trucks because of their edges in light-weight design, which can greatly help improve the fuel efficiency and decrease the gas emissions of vehicles; However, Mg alloys’ high sensitivity to the corrosive environments limit their penetration in automotive applications. Surface coating is one of the most effective and economic ways to protect Mg alloys from corrosion. Presently, the currently researched and commercial coatings that are specifically applied to Mg alloys in the automotive industry are reviewed in this paper. With some Mg automotive components subjected to corrosion and repeated load simultaneously, corrosion fatigue of coated Mg alloys are reviewed as well. Additionally, a part of attention in this review is given to the assessment approaches of corrosion and corrosion fatigue performance of coated Mg alloys for the purpose of material/surface coating system selection. Finally, some corrosion-related challenges for the growth of Mg alloys, future developments and research directions on surface coatings and corrosion fatigue testing approaches are discussed.


    加载中


    [1] Kumar DS, Sasanka CT, Ravindra K, et al. (2015) Magnesium and its alloys in automotive applications-a review. Am J Mater Sci Technol 4: 12–30.
    [2] Narayanan TS, Park IS, Lee MH (2015) Surface modification of magnesium and its alloys for biomedical applications: opportunities and challenges, In: Surface Modification of Magnesium and its Alloys for Biomedical Applications, Woodhead Publishing, 29–87.
    [3] Sakintuna B, Lamari-Darkrim F, Hirscher M (2007) Metal hydride materials for solid hydrogen storage: a review. Int J Hydrogen Energ 32: 1121–1140. doi: 10.1016/j.ijhydene.2006.11.022
    [4] Huie MM, Bock DC, Takeuchi ES, et al. (2015) Cathode materials for magnesium and magnesium-ion based batteries. Coordin Chem Rev 287: 15–27. doi: 10.1016/j.ccr.2014.11.005
    [5] Kulekci MK (2008) Magnesium and its alloys applications in automotive industry. Int J Adv Manuf Tech 39: 851–865. doi: 10.1007/s00170-007-1279-2
    [6] Asian Metal, Magnesium uses, 2018. Available from: http://metalpedia.asianmetal.com/metal/magnesium/application.shtml.
    [7] Brady MP, Joost WJ, David Warren C (2016) Insights from a recent meeting: current status and future directions in magnesium corrosion research. Corrosion 73: 452–462.
    [8] Merdian, Magnesium Alloys in the Automotive Market, 2015. Available from: https://www.amm.com/events/download.ashx/document/speaker/7981/a0ID000000X0kJUMAZ/Presentation.
    [9] Du CP, Xu DF (2013) Application of energy-saving magnesium alloy in automotive industry. Adv Mater Res 734: 2244–2247.
    [10] Blawert C, Hort N, Kainer KU (2004) Automotive applications of magnesium and its alloys. Trans Indian Inst Met 57: 397–408.
    [11] Luo AA (2002) Magnesium: current and potential automotive applications. JOM 54: 42–48.
    [12] Hussein RO, Northwood DO (2014) Improving the performance of magnesium alloys for automotive applications. WIT T Built Environ 137: 531–544.
    [13] Beecham M, Magnesium in car production-a weighting game, Bromsgrove (UK): Arop Ltd, 2017. Available from: https://www.just-auto.com/analysis/magnesium-in-car-production-a-weighting game_id176723.aspx.
    [14] Carpenter JA, Jackman J, Li NY, et al. (2007) Automotive Mg research and development in North America. Mater Sci Forum 546: 11–24.
    [15] Friedrich H, Schumann S (2001) Research for a "new age of magnesium" in the automotive industry. J Mater Process Tech 117: 276–281. doi: 10.1016/S0924-0136(01)00780-4
    [16] Brownell B, How Dangerous Are Magnesium Body Panels? 2016. Available from: http://www.thedrive.com/flat-six-society/6302/how-dangerous-are-magnesium-body-panels.
    [17] Luo AA (2013) Magnesium casting technology for structural applications. J Magnesium Alloy 1: 2–22. doi: 10.1016/j.jma.2013.02.002
    [18] Joost WJ, Krajewski PE (2017) Towards magnesium alloys for high-volume automotive applications. Scripta Mater 128: 107–112. doi: 10.1016/j.scriptamat.2016.07.035
    [19] Cole GS (2013) Magnesium (Mg) corrosion protection techniques in the automotive industry, In: Corrosion Prevention of Magnesium Alloys, Woodhead Publishing, 489–508.
    [20] Esmaily M, Svensson JE, Fajardo S, et al. (2017) Fundamentals and advances in magnesium alloy corrosion. Prog Mater Sci 89: 92–193. doi: 10.1016/j.pmatsci.2017.04.011
    [21] Song G, Atrens A (2003) Understanding magnesium corrosion-a framework for improved alloy performance. Adv Eng Mater 5: 837–858. doi: 10.1002/adem.200310405
    [22] Song G (2005) Recent progress in corrosion and protection of magnesium alloys. Adv Eng Mater 7: 563–586. doi: 10.1002/adem.200500013
    [23] Atrens A, Song GL, Cao F, et al. (2013) Advances in Mg corrosion and research suggestions. J Magnesium Alloy 1: 177–200. doi: 10.1016/j.jma.2013.09.003
    [24] Nowak P, Mosiałek M, Nawrat G (2015) Corrosion of magnesium and its alloys: new observations and ideas. Ochrona przed Korozją 11: 371–377.
    [25] Skar JI, Albright D (2016) Emerging trends in corrosion protection of magnesium die-castings, In: Essential Readings in Magnesium Technology, Springer, Cham, 585–591.
    [26] Gray J, Luan B (2002) Protective coatings on magnesium and its alloys-a critical review. J Alloy Compd 336: 88–113. doi: 10.1016/S0925-8388(01)01899-0
    [27] Abela S (2011) Protective coatings for magnesium alloys, In: Magnesium Alloys-Corrosion and Surface Treatments, InTech.
    [28] Chen XB, Birbilis N, Abbott TB (2011) Review of corrosion-resistant conversion coatings for magnesium and its alloys. Corrosion 67: 035005-1.
    [29] Blawert C, Dietzel W, Ghali E, et al. (2006) Anodizing treatments for magnesium alloys and their effect on corrosion resistance in various environments. Adv Eng Mater 8: 511–533. doi: 10.1002/adem.200500257
    [30] Gadow R, Gammel FJ, Lehnert F, et al. (2000) Coating system for magnesium diecastings in class A surface quality. Magnesium Alloy Appl 492–498.
    [31] Höche D, Nowak A, John-Schillings T (2013) Surface cleaning and pre-conditioning surface treatments to improve the corrosion resistance of magnesium (Mg) alloys, In: Corrosion Prevention of Magnesium Alloys, Woodhead Publishing, 87–109.
    [32] Wu CY, Zhang J (2011) State-of-art on corrosion and protection of magnesium alloys based on patent literatures. T Nonferr Metal Soc 21: 892–902. doi: 10.1016/S1003-6326(11)60799-1
    [33] Ke C, Song MS, Zeng RC, et al. (2019) Interfacial study of the formation mechanism of corrosion resistant strontium phosphate coatings upon Mg-3Al-4.3Ca-0.1Mn. Corros Sci 151: 143–153. doi: 10.1016/j.corsci.2019.02.024
    [34] Lehr IL, Saidman SB (2018) Corrosion protection of AZ91D magnesium alloy by a cerium-molybdenum coating-The effect of citric acid as an additive. J Magnesium Alloy 6: 356–365. doi: 10.1016/j.jma.2018.10.002
    [35] Zeng R, Lan Z, Kong L, et al. (2011) Characterization of calcium-modified zinc phosphate conversion coatings and their influences on corrosion resistance of AZ31 alloy. Surf Coat Tech 205: 3347–3355. doi: 10.1016/j.surfcoat.2010.11.027
    [36] Pommiers S, Frayret J, Castetbon A, et al. (2014) Alternative conversion coatings to chromate for the protection of magnesium alloys. Corros Sci 84: 135–146. doi: 10.1016/j.corsci.2014.03.021
    [37] Van Phuong N, Lee K, Chang D, et al. (2013) Zinc phosphate conversion coatings on magnesium alloys: a review. Met Mater Int 19: 273–281. doi: 10.1007/s12540-013-2023-0
    [38] Jian SY, Chu YR, Lin CS (2015) Permanganate conversion coating on AZ31 magnesium alloys with enhanced corrosion resistance. Corros Sci 93: 301–309. doi: 10.1016/j.corsci.2015.01.040
    [39] Zeng RC, Zhang F, Lan ZD, et al. (2014) Corrosion resistance of calcium-modified zinc phosphate conversion coatings on magnesium–aluminum alloys. Corros Sci 88: 452–459. doi: 10.1016/j.corsci.2014.08.007
    [40] Lin CS, Lin HC, Lin KM, et al. (2006) Formation and properties of stannate conversion coatings on AZ61 magnesium alloys. Corros Sci 48: 93–109. doi: 10.1016/j.corsci.2004.11.023
    [41] Greene JA, Vonk DR (2004) Conversion coatings including alkaline earth metal fluoride complexes. U.S. Patent No. 6,749,694. 2014-6-15.
    [42] Morris WC (1942) Process for coating metal surfaces. U.S. Patent No. 2,294,760. 1942-9-1.
    [43] Guerci G, Mus C, Stewart K (2000) Surface treatments for large automotive magnesium components. Magnesium Alloy Appl 484–491.
    [44] Rudd AL, Breslin CB, Mansfeld F (2000) The corrosion protection afforded by rare earth conversion coatings applied to magnesium. Corros Sci 42: 275–288. doi: 10.1016/S0010-938X(99)00076-1
    [45] Takenaka T, Ono T, Narazaki Y, et al. (2007) Improvement of corrosion resistance of magnesium metal by rare earth elements. Electrochim Acta 53: 117–121. doi: 10.1016/j.electacta.2007.03.027
    [46] Doerre M, Hibbitts L, Patrick G, et al. (2018) Advances in Automotive Conversion Coatings during Pretreatment of the Body Structure: A Review. Coatings 8: 405. doi: 10.3390/coatings8110405
    [47] Milošev I, Frankel GS (2018) Review-Conversion Coatings Based on Zirconium and/or Titanium. J Electrochem Soc 165: C127–C144. doi: 10.1149/2.0371803jes
    [48] Giles TR, Goodreau BH, Fristad WE, et al. (2009) An update of new conversion coating for the automotive industry. SAE Int J Mater Manuf 1: 575–581.
    [49] Brady MP, Leonard DN, Meyer III HM, et al. (2016) Advanced characterization study of commercial conversion and electrocoating structures on magnesium alloys AZ31B and ZE10A. Surf Coat Tech 294: 164–176. doi: 10.1016/j.surfcoat.2016.03.066
    [50] Li N, Chen X, Hubbert T, et al. (2005) 2005 Ford GT Magnesium Instrument Panel Cross Car Beam. SAE Technical Paper 2005-01-0341.
    [51] Environmental Friendly Conversion Coating on Mg Alloy. Institute of Metal Research Chinese Academy of Sciences, 2018. Available from: http://english.imr.cas.cn/news/newsrelease/201408/t20140829_126968.html.
    [52] Chiu KY, Wong MH, Cheng FT, et al. (2007) Characterization and corrosion studies of fluoride conversion coating on degradable Mg implants. Surf Coat Tech 202: 590–598. doi: 10.1016/j.surfcoat.2007.06.035
    [53] Chen XB, Yang HY, Abbott TB, et al. (2014) Corrosion protection of magnesium and its alloys by metal phosphate conversion coatings. Surf Eng 30: 871–879. doi: 10.1179/1743294413Y.0000000235
    [54] Dolan SE (1995) Composition and process for treating metals. U.S. Patent No. 5,449,415. 1995-9-12.
    [55] Walter M, Kurze P (2004) MAGPASS-COAT® as a Chrome-free Pre-treatment for Paint Layers and an Adhesive Primer for Subsequent Bonding. SAE Technical Paper 2004-01-0134.
    [56] Kainer KU (2007) Magnesium: proceedings of the 7th International Conference on Magnesium Alloys and their Applications, John Wiley & Sons.
    [57] Chemetall. Oxsilan® . Chemetall GmbH, 2018. Available from: http://www.chemetall.com/Products/Trademarks/Oxsilan/index.jsp.
    [58] CHEMEON TCP-HF. NALTIC Industrials, LLC, 2018. Available from: http://naltic.com/chemeon-tcp-hf.html.
    [59] SurTec. SurTec 650: Chromium (VI)-Free Passivation for Aluminium for the Electronics,-Automotive and Aerospace Industry. SurTec, 2018. Available from: https://www.surtec.com/en/products/product-highlights/628/.
    [60] ATOTECH. Interlox® 5707: Phosphate-free paint pretreatment for multimetal applocations. ATOTECH, 2018. Available from: https://www.atotech.com/paint-support-technologies/interlox-5707/.
    [61] PPG Industrial Coatings. ZIRCOBOND® and X-BONDTM: Zirconium-Based Thin-Film Pretreatment System. PPG Industrial Coatings, 2018. Available from: http://www.ppgindustrialcoatings.com/getmedia/591ca2e3-ec3d-4f60-9315-5bd2b9e37159/Zircobond-X-Bond-Sell-Sheet_v2-02-06-16LowRes.pdf.aspx.
    [62] Cui LY, Zeng RC, Guan SK, et al. (2017) Degradation mechanism of micro-arc oxidation coatings on biodegradable Mg-Ca alloys: The influence of porosity. J Alloy Compd 695: 2464–2476. doi: 10.1016/j.jallcom.2016.11.146
    [63] Ding ZY, Cui LY, Chen XB, et al. (2018) In vitro corrosion of micro-arc oxidation coating on Mg-1Li-1Ca alloy-The influence of intermetallic compound Mg2Ca. J Alloy Compd 764: 250–260. doi: 10.1016/j.jallcom.2018.06.073
    [64] Cui LY, Liu HP, Zhang WL, et al. (2017) Corrosion resistance of a superhydrophobic micro-arc oxidation coating on Mg-4Li-1Ca alloy. J Mater Sci Technol 33: 1263–1271. doi: 10.1016/j.jmst.2017.10.010
    [65] Cui LY, Gao SD, Li PP, et al. (2017) Corrosion resistance of a self-healing micro-arc oxidation/polymethyltrimethoxysilane composite coating on magnesium alloy AZ31. Corros Sci 118: 84–95. doi: 10.1016/j.corsci.2017.01.025
    [66] Xue Y, Pang X, Jiang B, et al. (2018) Corrosion performances of micro-arc oxidation coatings on Az31B, Az80 and Zk60 cast Mg alloys. CSME Conference Proceedings.
    [67] Xue Y, Pang X, Jiang B, et al. (2018) Influence of micro-arc oxidation coatings on corrosion performances of AZ80 cast alloy. Int J Electrochem Sc 13: 7265–7281.
    [68] Song GL, Shi Z (2013) Anodization and corrosion of magnesium (Mg) alloys, In: Corrosion Prevention of Magnesium Alloys, Woodhead Publishing, 232–281.
    [69] Jiang BL, Ge YF (2013) Micro-arc oxidation (MAO) to improve the corrosion resistance of magnesium (Mg) alloys, In: Corrosion Prevention of Magnesium Alloys, Woodhead Publishing, 163–196.
    [70] Shapiro J. Alodine EC2 Prevents Corrosion on Volvo Penta's Lighter Greener Pleasure Craft. MachineDesign, 2010. Available from: https://www.machinedesign.com/news/alodine-ec2-prevents-corrosion-volvo-penta-s-lighter-greener-pleasure-craft.
    [71] Coating Applications. Technology Applications Group, 2018. Available from: http://www.tagnite.com/applications/#?201,115.
    [72] Azumi K, Elsentriecy HH, Tang J (2013) Plating techniques to protect magnesium (Mg) alloys from corrosion, In: Corrosion Prevention of Magnesium Alloys, Woodhead Publishing, 347–369.
    [73] Chen XB, Easton MA, Birbilis N, et al. (2013) Corrosion-resistant electrochemical plating of magnesium (Mg) alloys, In: Corrosion Prevention of Magnesium Alloys, Woodhead Publishing, 315–346.
    [74] El Mahallawy N (2008) Surface Treatment of Magnesium Alloys by Electroless Ni–P Plating Technique with Emphasis on Zinc Pre-treatment: a Review. Key Eng Mater 384: 241–262. doi: 10.4028/www.scientific.net/KEM.384.241
    [75] Lei XP, Yu G, Zhu YP, et al. (2010) Successful cyanide free plating protocols on magnesium alloys. T IMF 88: 75–80. doi: 10.1179/174591910X12646055765330
    [76] Hu RG, Zhang S, Bu JF, et al. (2012) Recent progress in corrosion protection of magnesium alloys by organic coatings. Prog Org Coat 73: 129–141. doi: 10.1016/j.porgcoat.2011.10.011
    [77] Wang GG, Stewart K, Berkmortel R, et al. (2001) Corrosion prevention for external magnesium automotive components. SAE Technical Paper 2001-01-0421.
    [78] Magnesium Coatings Suppliers. Thomas, 2018. Available from: https://www.thomasnet.com/products/magnesium-coatings-15800535-1.html.
    [79] High pressure: magnesium diecasting from STIHL. STIHL team, 2017. Available from: http://blog.stihl.com/products-/2017/11/stihl-magnesium-diecasting-plant/.
    [80] Guo L, Wu W, Zhou Y, et al. (2018) Layered double hydroxide coatings on magnesium alloys: A review. J Mater Sci Technol 34: 1455–1466. doi: 10.1016/j.jmst.2018.03.003
    [81] Zhang G, Wu L, Tang A, et al. (2017) A novel approach to fabricate protective layered double hydroxide films on the surface of anodized Mg‐Al alloy. Adv Mater Interfaces 4: 1700163. doi: 10.1002/admi.201700163
    [82] Wu L, Zhang G, Tang A, et al. (2017) Communication-fabrication of protective layered double hydroxide films by conversion of anodic films on magnesium alloy. J Electrochem Soc 164: C339–C341. doi: 10.1149/2.0921707jes
    [83] Wu L, Yang D, Zhang G, et al. (2018) Fabrication and characterization of Mg-M layered double hydroxide films on anodized magnesium alloy AZ31. Appl Surf Sci 431: 177–186. doi: 10.1016/j.apsusc.2017.06.244
    [84] Zeng RC, Liu ZG, Zhang F, et al. (2014) Corrosion of molybdate intercalated hydrotalcite coating on AZ31 Mg alloy. J Mater Chem A 2: 13049–13057. doi: 10.1039/C4TA01341G
    [85] Adsul SH, Raju KRCS, Sarada BV, et al. (2018) Evaluation of self-healing properties of inhibitor loaded nanoclay-based anticorrosive coatings on magnesium alloy AZ91D. J Magnesium Alloy 6: 299–308. doi: 10.1016/j.jma.2018.05.003
    [86] Bala N, Singh H, Karthikeyan J, et al. (2014) Cold spray coating process for corrosion protection: a review. Surf Eng 30: 414–421. doi: 10.1179/1743294413Y.0000000148
    [87] Hassani-Gangaraj SM, Moridi A, Guagliano M (2015) Critical review of corrosion protection by cold spray coatings. Surf Eng 31: 803–815. doi: 10.1179/1743294415Y.0000000018
    [88] Spencer K, Fabijanic DM, Zhang MX (2009) The use of Al–Al2O3 cold spray coatings to improve the surface properties of magnesium alloys. Surf Coat Tech 204: 336–344. doi: 10.1016/j.surfcoat.2009.07.032
    [89] Wang Q, Spencer K, Birbilis N, et al. (2010) The influence of ceramic particles on bond strength of cold spray composite coatings on AZ91 alloy substrate. Surf Coat Tech 205: 50–56. doi: 10.1016/j.surfcoat.2010.06.008
    [90] DeForce BS, Eden TJ, Potter JK (2011) Cold spray Al-5% Mg coatings for the corrosion protection of magnesium alloys. J Therm Spray Techn 20: 1352–1358. doi: 10.1007/s11666-011-9675-4
    [91] Bu H, Yandouzi M, Lu C, et al. (2012) Cold spray blended Al + Mg17Al12 coating for corrosion protection of AZ91D magnesium alloy. Surf Coat Tech 207: 155–162. doi: 10.1016/j.surfcoat.2012.06.050
    [92] Zhan W, Tian F, Ou-Yang G, et al. (2018) Effects of Nickel Additive on Micro-Arc Oxidation Coating of AZ63B Magnesium Alloy. Int J Precis Eng Man 19: 1081–1087. doi: 10.1007/s12541-018-0128-6
    [93] Tomozawa M, Hiromoto S (2011) Microstructure of hydroxyapatite-and octacalcium phosphate-coatings formed on magnesium by a hydrothermal treatment at various pH values. Acta Mater 59: 355–363. doi: 10.1016/j.actamat.2010.09.041
    [94] Cui X, Liu C, Yang R, et al. (2013) Duplex-layered manganese phosphate conversion coating on AZ31 Mg alloy and its initial formation mechanism. Corros Sci 76: 474–485. doi: 10.1016/j.corsci.2013.07.024
    [95] Lee YL, Chu YR, Li WC, et al. (2013) Effect of permanganate concentration on the formation and properties of phosphate/permanganate conversion coating on AZ31 magnesium alloy. Corros Sci 70: 74–81. doi: 10.1016/j.corsci.2013.01.014
    [96] Zhao M, Wu S, Luo JR, et al. (2006) A chromium-free conversion coating of magnesium alloy by a phosphate–permanganate solution. Surf Coat Tech 200: 5407–5412. doi: 10.1016/j.surfcoat.2005.07.064
    [97] Cui X, Liu C, Yang R, et al. (2012) Phosphate film free of chromate, fluoride and nitrite on AZ31 magnesium alloy and its corrosion resistance. T Nonferr Metal Soc 22: 2713–2718. doi: 10.1016/S1003-6326(11)61522-7
    [98] Li L, Qu Q, Fang Z, et al. (2012) Enhanced corrosion resistance of AZ31B magnesium alloy by cooperation of rare earth cerium and stannate conversion coating. Int J Electrochem Sci 7: 12690–12705.
    [99] Zeng R, Yan HU, Zhang F, et al. (2016) Corrosion resistance of cerium-doped zinc calcium phosphate chemical conversion coatings on AZ31 magnesium alloy. T Nonferr Metal Soc 26: 472–483. doi: 10.1016/S1003-6326(16)64102-X
    [100] Ba Z, Dong Q, Zhang X, et al. (2017) Cerium-based modification treatment of Mg-Al hydrotalcite film on AZ91D Mg alloy assisted with alternating electric field. J Alloy Compd 695: 106–113. doi: 10.1016/j.jallcom.2016.10.139
    [101] Ardelean H, Frateur I, Marcus P (2008) Corrosion protection of magnesium alloys by cerium, zirconium and niobium-based conversion coatings. Corros Sci 50: 1907–1918. doi: 10.1016/j.corsci.2008.03.015
    [102] Zhao M, Wu S, An P, et al. (2006) Microstructure and corrosion resistance of a chromium-free multi-elements complex coating on AZ91D magnesium alloy. Mater Chem Phys 99: 54–60. doi: 10.1016/j.matchemphys.2005.08.078
    [103] Jiang X, Guo R, Jiang S (2015) Microstructure and corrosion resistance of Ce–V conversion coating on AZ31 magnesium alloy. Appl Surf Sci 341: 166–174. doi: 10.1016/j.apsusc.2015.02.195
    [104] Zhao M, Li J, He G, et al. (2013) Nano Al2O3/phosphate composite conversion coating formed on magnesium alloy for enhancing corrosion resistance. J Electrochem Soc 160: C553–C559. doi: 10.1149/2.059311jes
    [105] Li K, Liu J, Lei T, et al. (2015) Optimization of process factors for self-healing vanadium-based conversion coating on AZ31 magnesium alloy. Appl Surf Sci 353: 811–819. doi: 10.1016/j.apsusc.2015.07.052
    [106] Cheng Y, Wu H, Chen Z, et al. (2006) Phosphating process of AZ31 magnesium alloy and corrosion resistance of coatings. T Nonferr Metal Soc 16: 1086–1091. doi: 10.1016/S1003-6326(06)60382-8
    [107] Amini R, Sarabi AA (2011) The corrosion properties of phosphate coating on AZ31 magnesium alloy: the effect of sodium dodecyl sulfate (SDS) as an eco-friendly accelerating agent. Appl Surf Sci 257: 7134–7139. doi: 10.1016/j.apsusc.2011.03.072
    [108] Wang C, Zhu S, Jiang F, et al. (2009) Cerium conversion coatings for AZ91D magnesium alloy in ethanol solution and its corrosion resistance. Corros Sci 51: 2916–2923. doi: 10.1016/j.corsci.2009.08.003
    [109] Hsiao HY, Tsai WT (2005) Characterization of anodic films formed on AZ91D magnesium alloy. Surf Coat Tech 190: 299–308. doi: 10.1016/j.surfcoat.2004.03.010
    [110] Zhang Y, Yan C, Wang F, et al. (2002) Study on the environmentally friendly anodizing of AZ91D magnesium alloy. Surf Coat Tech 161: 36–43. doi: 10.1016/S0257-8972(02)00342-0
    [111] Wu H, Cheng Y, Li L, et al. (2007) The anodization of ZK60 magnesium alloy in alkaline solution containing silicate and the corrosion properties of the anodized films. Appl Surf Sci 253: 9387–9394. doi: 10.1016/j.apsusc.2007.05.085
    [112] Su Y, Li G, Lian J (2012) A chemical conversion hydroxyapatite coating on AZ60 magnesium alloy and its electrochemical corrosion behaviour. Int J Electrochem Sci 7: 11497–11511.
    [113] Guo X, Du K, Wang Y, et al. (2012) A new nanoparticle penetrant used for plasma electrolytic oxidation film coated on AZ31 Mg alloy in service environment. Surf Coat Tech 206: 4833–4839. doi: 10.1016/j.surfcoat.2012.05.063
    [114] Sun RX, Wang PF, Zhao DD, et al. (2015) An environment‐friendly calcium phosphate conversion coating on AZ91D alloy and its corrosion resistance. Mater Corros 66: 383–386. doi: 10.1002/maco.201307424
    [115] Mu S, Du J, Jiang H, et al. (2014) Composition analysis and corrosion performance of a Mo–Ce conversion coating on AZ91 magnesium alloy. Surf Coat Tech 254: 364–370. doi: 10.1016/j.surfcoat.2014.06.044
    [116] Hu J, Li Q, Zhong X, et al. (2009) Composite anticorrosion coatings for AZ91D magnesium alloy with molybdate conversion coating and silicon sol–gel coatings. Prog Org Coat 66: 199–205. doi: 10.1016/j.porgcoat.2009.07.003
    [117] Seifzadeh D, Rajabalizadeh Z (2013) Environmentally-friendly method for electroless Ni–P plating on magnesium alloy. Surf Coat Tech 218: 119–126. doi: 10.1016/j.surfcoat.2012.12.039
    [118] Wang L, Zhang K, Sun W, et al. (2013) Hydrothermal synthesis of corrosion resistant hydrotalcite conversion coating on AZ91D alloy. Mater Lett 106: 111–114. doi: 10.1016/j.matlet.2013.05.018
    [119] Gao HF, Tan HQ, Li J, et al. (2012) Synergistic effect of cerium conversion coating and phytic acid conversion coating on AZ31B magnesium alloy. Surf Coat Tech 212: 32–36. doi: 10.1016/j.surfcoat.2012.09.008
    [120] Sun J, Wang G (2014) Preparation and corrosion resistance of cerium conversion coatings on AZ91D magnesium alloy by a cathodic electrochemical treatment. Surf Coat Tech 254: 42–48. doi: 10.1016/j.surfcoat.2014.05.054
    [121] Sun J, Wang G (2015) Preparation and characterization of a cerium conversion film on magnesium alloy. Anti-Corros Method M 62: 253–258. doi: 10.1108/ACMM-12-2013-1336
    [122] Pan SJ, Tsai WT, Kuo JC, et al. (2013) Material characteristics and corrosion performance of heat-treated Al-Zn coatings electrodeposited on AZ91D magnesium alloy from an ionic liquid. J Electrochem Soc 160: D320–D325. doi: 10.1149/2.100308jes
    [123] Tao Y, Xiong T, Sun C, et al. (2010) Microstructure and corrosion performance of a cold sprayed aluminium coating on AZ91D magnesium alloy. Corros Sci 52: 3191–3197. doi: 10.1016/j.corsci.2010.05.023
    [124] Krishna LR, Poshal G, Jyothirmayi A, et al. (2013) Compositionally modulated CGDS + MAO duplex coatings for corrosion protection of AZ91 magnesium alloy. J Alloy Compd 578: 355–361. doi: 10.1016/j.jallcom.2013.06.036
    [125] Tao Y, Xiong T, Sun C, et al. (2009) Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy. Appl Surf Sci 256: 261–266. doi: 10.1016/j.apsusc.2009.08.012
    [126] Lei XP, Yu G, Zhu YP, et al. (2010) Successful cyanide free plating protocols on magnesium alloys. T IMF 88: 75–80. doi: 10.1179/174591910X12646055765330
    [127] Chen F, Zhou H, Yao B, et al. (2007) Corrosion resistance property of the ceramic coating obtained through microarc oxidation on the AZ31 magnesium alloy surfaces. Surf Coat Tech 201: 4905–4908. doi: 10.1016/j.surfcoat.2006.07.079
    [128] Zhao H, Huang Z, Cui J (2007) A new method for electroless Ni–P plating on AZ31 magnesium alloy. Surf Coat Tech 202: 133–139. doi: 10.1016/j.surfcoat.2007.05.001
    [129] Liu Q, Chen D, Kang Z (2015) One-step electrodeposition process to fabricate corrosion-resistant superhydrophobic surface on magnesium alloy. ACS Appl Mater Inter 7: 1859–1867. doi: 10.1021/am507586u
    [130] Zhang J, Wu C (2010) Corrosion and Protection of Magnesium Alloys-A Review of the Patent Literature. Recent Pat Corros Sci 2: 55–68. doi: 10.2174/1877610801002010055
    [131] Forsmark JH, Li M, Su X, et al. (2014) The USAMP Magnesium Front End Research and Development Project-Results of the Magnesium "Demonstration" Structure, In: Magnesium Technology, Springer, Cham, 517–524.
    [132] Montemor MF (2014) Functional and smart coatings for corrosion protection: a review of recent advances. Surf Coat Tech 258: 17–37. doi: 10.1016/j.surfcoat.2014.06.031
    [133] Jiang C, Cao Y, Xiao G, et al. (2017) A review on the application of inorganic nanoparticles in chemical surface coatings on metallic substrates. RSC Adv 7: 7531–7539. doi: 10.1039/C6RA25841G
    [134] Unigovski Y, Eliezer A, Abramov E, et al. (2003) Corrosion fatigue of extruded magnesium alloys. Mat Sci Eng A-Struct 360: 132–139. doi: 10.1016/S0921-5093(03)00409-X
    [135] Nan ZY, Ishihara S, Goshima T (2008) Corrosion fatigue behavior of extruded magnesium alloy AZ31 in sodium chloride solution. Int J Fatigue 30: 1181–1188. doi: 10.1016/j.ijfatigue.2007.09.005
    [136] Bhuiyan MS, Mutoh Y, Murai T, et al. (2010) Corrosion fatigue behavior of extruded magnesium alloy AZ80-T5 in a 5% NaCl environment. Eng Fract Mech 77: 1567–1576. doi: 10.1016/j.engfracmech.2010.03.032
    [137] Chamos AN, Pantelakis SG, Spiliadis V (2010) Fatigue behavior of bare and pre-corroded magnesium alloy AZ31. Mater Design 31: 4130–4137. doi: 10.1016/j.matdes.2010.04.031
    [138] He XL, Wei YH, Hou LF, et al. (2014) Investigation on corrosion fatigue property of epoxy coated AZ31 magnesium alloy in sodium sulfate solution. Theor Appl Fract Mec 70: 39–48. doi: 10.1016/j.tafmec.2014.03.002
    [139] He XL, Wei YH, Hou LF, et al. (2014) Corrosion fatigue behavior of epoxy-coated Mg–3Al–1Zn alloy in NaCl solution. Rare Metals 33: 276–286. doi: 10.1007/s12598-014-0278-3
    [140] He XL, Wei YH, Hou LF, et al. (2014) Corrosion fatigue behavior of epoxy-coated Mg–3Al–1Zn alloy in gear oil. T Nonferr Metal Soc 24: 3429–3440. doi: 10.1016/S1003-6326(14)63486-5
    [141] Uematsu Y, Kakiuchi T, Teratani T, et al. (2011) Improvement of corrosion fatigue strength of magnesium alloy by multilayer diamond-like carbon coatings. Surf Coat Tech 205: 2778–2784. doi: 10.1016/j.surfcoat.2010.10.040
    [142] Dayani SB, Shaha SK, Ghelichi R, et al. (2018) The impact of AA7075 cold spray coating on the fatigue life of AZ31B cast alloy. Surf Coat Tech 337: 150–158. doi: 10.1016/j.surfcoat.2018.01.008
    [143] Borhan Dayani S (2017) Improvement of fatigue and corrosion-fatigue resistance of AZ31B cast alloy by cold spray coating and top coating [Master thesis]. University of Waterloo.
    [144] Ishihara S, Masuda K, Namito T, et al. (2014) On corrosion fatigue strength of the anodized and painted Mg alloy. Int J Fatigue 66: 252–258. doi: 10.1016/j.ijfatigue.2014.03.007
    [145] Khan SA, Miyashita Y, Mutoh Y, et al. (2008) Fatigue behavior of anodized AM60 magnesium alloy under humid environment. Mat Sci Eng A-Struct 498: 377–383. doi: 10.1016/j.msea.2008.08.015
    [146] Khan SA, Miyashita Y, Mutoh Y (2015) Corrosion fatigue behavior of AM60 magnesium alloy with anodizing layer and chemical‐conversion‐coating layer. Mater Corros 66: 940–948. doi: 10.1002/maco.201407946
    [147] Bhuiyan MS, Mutoh Y (2011) Corrosion fatigue behavior of conversion coated and painted AZ61 magnesium alloy. Int J Fatigue 33: 1548–1556. doi: 10.1016/j.ijfatigue.2011.06.011
    [148] Ishihara S, Notoya H, Namito T (2011) Improvement in Corrosion Fatigue Resistance of Mg Alloy due to Plating, In: Magnesium Alloys-Corrosion and Surface Treatments, IntechOpen.
    [149] Yerokhin AL, Shatrov A, Samsonov V, et al. (2004) Fatigue properties of Keronite® coatings on a magnesium alloy. Surf Coat Tech 182: 78–84.
    [150] Bhuiyan MS, Ostuka Y, Mutoh Y, et al. (2010) Corrosion fatigue behavior of conversion coated AZ61 magnesium alloy. Mat Sci Eng A-Struct 527: 4978–4984. doi: 10.1016/j.msea.2010.04.059
    [151] Khan SA, Bhuiyan MS, Miyashita Y, et al. (2011) Corrosion fatigue behavior of die-cast and shot-blasted AM60 magnesium alloy. Mat Sci Eng A-Struct 528: 1961–1966. doi: 10.1016/j.msea.2010.11.033
    [152] Shaha SK, Dayani SB, Jahed H (2018) Influence of Cold Spray on the Enhancement of Corrosion Fatigue of the AZ31B Cast Mg Alloy, In: TMS Annual Meeting & Exhibition, Springer, Cham, 541–550.
    [153] Diab M, Pang X, Jahed H (2017) The effect of pure aluminum cold spray coating on corrosion and corrosion fatigue of magnesium (3% Al-1% Zn) extrusion. Surf Coat Tech 309: 423–435. doi: 10.1016/j.surfcoat.2016.11.014
    [154] Němcová A, Skeldon P, Thompson GE, et al. (2014) Influence of plasma electrolytic oxidation on fatigue performance of AZ61 magnesium alloy. Corros Sci 82: 58–66. doi: 10.1016/j.corsci.2013.12.019
    [155] Klein M, Lu X, Blawert C, et al. (2017) Influence of plasma electrolytic oxidation coatings on fatigue performance of AZ31 Mg alloy. Mater Corros 68: 50–57. doi: 10.1002/maco.201609088
    [156] Okada H, Uematsu Y, Tokaji K (2010) Fatigue behaviour in AZ80A magnesium alloy with DLC/thermally splayed WC-12Co hybrid coating. Procedia Eng 2: 283–290. doi: 10.1016/j.proeng.2010.03.031
    [157] Ceschini L, Morri A, Angelini V, et al. (2017) Fatigue behavior of the rare earth rich EV31A Mg alloy: influence of plasma electrolytic oxidation. Metals 7: 212. doi: 10.3390/met7060212
    [158] Huang CA, Chuang CH, Yeh YH, et al. (2016) Low-cycle fatigue fracture behavior of a Mg alloy (AZ61) after alkaline Cu, alkaline followed by acidic Cu, Ni/Cu, and Cr-C/Cu electroplating. Mat Sci Eng A-Struct 662: 111–119. doi: 10.1016/j.msea.2016.03.064
    [159] Chen YL, Zhang Y, Li Y, et al. (2011) Influences of micro-arc oxidation on pre-corroded fatigue property of magnesium alloy AZ91D. Adv Mater Res 152: 51–57.
    [160] Wang BJ, Wang SD, Xu DK, et al. (2017) Recent progress in fatigue behavior of Mg alloys in air and aqueous media: A review. J Mater Sci Technol 33: 1075–1086. doi: 10.1016/j.jmst.2017.07.017
    [161] LeBozec N, Blandin N, Thierry D (2008) Accelerated corrosion tests in the automotive industry: a comparison of the performance towards cosmetic corrosion. Mater Corros 59: 889–894. doi: 10.1002/maco.200804168
    [162] ASTM B117 (1997) Standard Practice for Operating Salt Spray (Fog) Apparatus. ASTM International.
    [163] ASTM D870 (2009) Standard Practice for Testing Water Resistance of Coatings Using Water Immersion. ASTM International.
    [164] ASTM D (2002) Standard practice for testing water resistance of coatings in 100% relative humidity.
    [165] Liu M, Uggowitzer PJ, Nagasekhar AV, et al. (2009) Calculated phase diagrams and the corrosion of die-cast Mg–Al alloys. Corros Sci 51: 602–619. doi: 10.1016/j.corsci.2008.12.015
    [166] VDA 233-102 Cyclic corrosion testing of materials and components in automotive construction. ascot, 2018. Available from: http://www.vda233-102.com/.
    [167] Townsend HE, McCune DC (1997) Round-Robin Evaluation of a New Standard Laboratory Test for Cosmetic Corrosion. SAE Trans 106: 1249–1262.
    [168] Bovard FS, Smith KA, Courval GJ, et al. (2010) Cosmetic Corrosion Test for Aluminum Autobody Panels. SAE Intl J Passeng Cars-Mech Syst 3: 544–553. doi: 10.4271/2010-01-0726
    [169] Weiler JP, Wang G, Berkmortel R (2018) Assessment of OEM Corrosion Test Protocols for Magnesium Substrates. SAE Technical Paper 2018-01-0103.
    [170] Standard Corrosion Tests, 2018. Available from: https://www.ascott-analytical.com/test_standard/.
    [171] LeBozec N, Blandin N, Thierry D (2008) Accelerated corrosion tests in the automotive industry: a comparison of the performance towards cosmetic corrosion. Mater Corros 59: 889–894. doi: 10.1002/maco.200804168
    [172] SAE J2334 (2003) Laboratory Cyclic Corrosion Test.
    [173] Cyclic Corrosion Test. Quebec (CA): Micom Laboratories Inc., 2018. Available from: https://www.micomlab.com/micom-testing/cyclic-corrosion-testing/.
    [174] Micone N, De Waele W (2017) Evaluation of Methodologies to Accelerate Corrosion Assisted Fatigue Experiments. Exp Mech 57: 547–557. doi: 10.1007/s11340-016-0241-3
    [175] LeBozec N, Thierry D (2015) A new device for simultaneous corrosion fatigue testing of joined materials in accelerated corrosion tests. Mater Corros 66: 893–898. doi: 10.1002/maco.201407984
  • Reader Comments
  • © 2019 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索

Metrics

Article views(10711) PDF downloads(3262) Cited by(25)

Article outline

Figures and Tables

Figures(12)  /  Tables(7)

Other Articles By Authors

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog