Research article

Densification behaviour of sintered aluminum composites during hot deformation

  • Received: 07 July 2018 Accepted: 09 August 2018 Published: 12 September 2018
  • In this study, an investigation on the densification behavior and forming limit of powder metallurgy composites containing hard carbide particles were carried out. The selected composite materials are Al4TiC, Al4WC, Al4Fe3C and Al4Mo2C. The compacts of 0.82 and 0.86 relative density and 0.4 and 0.6 aspect ratio were prepared on a 1-MN capacity hydraulic press using suitable die-set assembly. Sintering was carried out at 594 ℃ for 60 minutes in an electrical muffle furnace. Hot upsetting was carried out at the sintering temperature immediately after the sintering process and the forming process was stopped once visible cracks were seen on the free surface. Flat dies on the upper and lower surface were employed under dry friction conditions during hot upsetting. Finally, the densification behavior and forming limit of sintered-forged aluminium composite preforms is presented in this research work. It was concretely noted that Al4TiC produced the best density amongst all the above mentioned aluminium composites. Further, it was seen that Al4Mo2C and Al4WC produced good final height and diameter strain at fracture.

    Citation: Sumesh Narayan, Ananthanarayanan Rajeshkannan. Densification behaviour of sintered aluminum composites during hot deformation[J]. AIMS Materials Science, 2018, 5(5): 902-915. doi: 10.3934/matersci.2018.5.902

    Related Papers:

  • In this study, an investigation on the densification behavior and forming limit of powder metallurgy composites containing hard carbide particles were carried out. The selected composite materials are Al4TiC, Al4WC, Al4Fe3C and Al4Mo2C. The compacts of 0.82 and 0.86 relative density and 0.4 and 0.6 aspect ratio were prepared on a 1-MN capacity hydraulic press using suitable die-set assembly. Sintering was carried out at 594 ℃ for 60 minutes in an electrical muffle furnace. Hot upsetting was carried out at the sintering temperature immediately after the sintering process and the forming process was stopped once visible cracks were seen on the free surface. Flat dies on the upper and lower surface were employed under dry friction conditions during hot upsetting. Finally, the densification behavior and forming limit of sintered-forged aluminium composite preforms is presented in this research work. It was concretely noted that Al4TiC produced the best density amongst all the above mentioned aluminium composites. Further, it was seen that Al4Mo2C and Al4WC produced good final height and diameter strain at fracture.


    加载中
    [1] Kok M (2005) Production and mechanical properties of Al2O3 particle-reinforced 2024 aluminium alloy composites. J Mater Process Tech 161: 381–387. doi: 10.1016/j.jmatprotec.2004.07.068
    [2] Torres B, Lieblich M, Ibanez J, et al. (2002) Mechanical properties of some powder metallurgy aluminide and silicide reinforced 2124 aluminium matrix composites. Scripta Mater 47: 45–49. doi: 10.1016/S1359-6462(02)00095-7
    [3] Davis G (2012) Design and material utilization, In: Davis G, Materials for automobile bodies, London: Butterworth Heinemann, 17–91.
    [4] Gururaja MN, Rao ANH (2012) A review on recent applications and future prospectus of hybrid composites. Int J Soft Comput Eng 1: 352–355.
    [5] Sahin Y (2003) Preparation and some properties of SiC particle reinforced aluminium alloy composites. Mater Design 24: 671–679. doi: 10.1016/S0261-3069(03)00156-0
    [6] Eslamian M, Rak J, Ashgriz N (2008) Preparation of aluminium/silicon carbide metal matrix composites using centrifugal atomization. Powder Technol 184: 11–20. doi: 10.1016/j.powtec.2007.07.045
    [7] Narayanasamy R, Senthilkumar V, Pandey KS (2007) Effect of titanium carbide particle addition on the densification behaviour of sintered P/M high strength steel preforms during cold upset forming. Mat Sci Eng A-Struct 456: 180–188. doi: 10.1016/j.msea.2006.11.118
    [8] Zhang XQ, Peng YH, Li MQ, et al. (2009) Study of workability limits of porous materials under different upsetting conditions by compressible rigid plastic finite element method. J Mater Eng Perform 9: 164–169.
    [9] Senthilkumar V, Narayanasamy R (2008) Influence of titanium carbide particles addition on the forging behaviour of powder metallurgy composite steels. P I Mech Eng B-J Eng 222: 1333–1345.
    [10] Gopalakrishnan S, Murugan N (2011) Prediction of tensile strength of friction stir welded aluminium matrix TiC particulate reinforced composite. Mater Design 32: 462–467. doi: 10.1016/j.matdes.2010.05.055
    [11] Asavavisithchai S, Opa A (2010) Effect of TiC particles on foamability and compressive properties of aluminium foams. Chiang Mai J Sci 37: 213–221.
    [12] Yusoff M, Othman R, Hussain Z (2011) Mechanical alloying and sintering of nanostructured tungsten carbide-reinforced copper composite and its characterization. Mater Design 32: 3293–3298. doi: 10.1016/j.matdes.2011.02.025
    [13] Dannininger H, Gierl C, Salak A (2009) Relationship between apparent hardness and tensile strength in P/M iron and steels sintered at standard temperatures. Powder Metall Prog 9: 1–13.
    [14] Dannininger H, Jangg G, Weiss B, et al. (1993) Microstructure and mechanical properties of sintered iron. I: Basic consideration and review of literature. Powder Metall Int 25: 111–117.
    [15] Dannininger H, Jangg G, Weiss B, et al. (1993) Microstructure and mechanical properties of sintered iron. II: Experimental study. Powder Metall Int 25: 219–223.
    [16] Rahimian M, Ehsani N, Parvin N, et al. (2009) The effect of particle size, sintering temperature and sintering time on the properties of Al–Al2O3 composites, made by powder metallurgy. J Mater Process Tech 209: 5387–5393. doi: 10.1016/j.jmatprotec.2009.04.007
    [17] Narayanasamy R, Ramesh T, Pandey KS (2005) Some aspects on workability of aluminium–iron powder metallurgy composite during cold upsetting. Mat Sci Eng A-Struct 391: 418–426.
    [18] Rahman MA, El-Sheikh MN (1995) Workability in forging of powder metallurgy compacts. J Mater Process Tech 54: 97–102. doi: 10.1016/0924-0136(95)01926-X
    [19] Rudenko N, Laptev A (2011) Compaction and properties of highly porous powder parts produced with various pore formers. Mech Test Diagn 1: 82–87.
    [20] Narayan S, Rajeshkannan A (2011) Densification behavior in forming of sintered iron–0.35% carbon powder metallurgy preform cold upsetting. Mater Design 32: 1006–1013.
    [21] Rajeshkannan A, Narayan S (2009) Strain hardening behavior in sintered Fe–0.8%C–1.0%Si–0.8%Cu powder metallurgy preform during cold upsetting. P I Mech Eng B-J Eng 223: 1567–1574.
    [22] Raj APM, Selvakumar N, Narayanasamy R, et al. (2013) Experimental investigation on workability and strain hardening behaviour of Fe–C–Mn sintered composites with different percentage of carbon and manganese content. Mater Design 49: 791–801. doi: 10.1016/j.matdes.2013.02.002
    [23] Rajeshkannan A, Rai NS, Chand M, et al. (2014) Densification behavior of sintered-forged aluminium composite preforms. P I Mech Eng B-J Eng 228: 441–449.
    [24] Al-Qureshi HA, Galiotto A, Klein AN (2005) On the mechanics of cold die compaction for powder metallurgy. J Mater Process Tech 166: 135–143. doi: 10.1016/j.jmatprotec.2004.08.009
    [25] Al-Qureshi HA, Soares MRF, Hotza D, et al. (2008) Analyses of the fundamental parameters of cold die compaction of powder metallurgy. J Mater Process Tech 199: 417–424. doi: 10.1016/j.jmatprotec.2007.08.030
    [26] Zhou ZY, Chen PQ, Zhou WB, et al. (2002) Densification model for porous metallic powder materials. J Mater Process Tech 129: 385–388. doi: 10.1016/S0924-0136(02)00697-0
    [27] Hua L, Qin X, Mao H, et al. (2006) Plastic deformation and yield criterion for compressible sintered powder materials. J Mater Process Tech 180: 174–178. doi: 10.1016/j.jmatprotec.2006.06.001
    [28] Lewis RW, Khoei AR (2001) A plasticity model for metal powder forming processes. Int J Plasticity 17: 1659–1692.
    [29] Narayan S, Rajeshkannan A (2017) Studies on formability of sintered aluminium composites during hot deformation using strain hardening parameters. J Mater Res Technol 6: 101–107. doi: 10.1016/j.jmrt.2016.03.012
    [30] Narayan S, Rajeshkannan A (2016) Workability studies of sintered aluminium composites during hot deformation. P I Mech Eng B-J Eng 230: 494–504.
  • Reader Comments
  • © 2018 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索

Metrics

Article views(3285) PDF downloads(827) Cited by(2)

Article outline

Figures and Tables

Figures(10)  /  Tables(1)

Other Articles By Authors

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog