Export file:

Format

  • RIS(for EndNote,Reference Manager,ProCite)
  • BibTex
  • Text

Content

  • Citation Only
  • Citation and Abstract

Scratch behavior of soft metallic materials

Chair of Materials Technology, Ruhr-Universität Bochum, Bochum, Germany

Topical Section: Soft and Polymeric Materials

This paper investigates the scratch resistance of metallic materials that include pure iron and the two steels AISI 1045 and AISI 304L. To investigate the deformation behavior under scratch load, tests were performed with a gradually increasing scratch load combined with subsequent analysis by scanning-electron microscopy and by atomic force microscopy. The fab value was determined to quantify the active micro-mechanisms of abrasion. In addition, tensile tests, hardness measurements, and nanoindentation experiments were conducted to correlate the scratch behavior with the mechanical properties. It was shown that there is no general correlation between the individual mechanical properties and the results of the scratch tests. However, the results revealed that work hardening of metallic materials plays a significant role, especially in the development of pile-up, and thus it greatly affects the active micro-mechanisms. The specific work of fracture at least correctly reproduces the order of scratch depth and the tangential force of the investigated materials.
  Figure/Table
  Supplementary
  Article Metrics

References

1. Zum Gahr K-H (1987) Microstructure and wear of materials, Elsevier.

2. Rabinowicz E (1965) Friction and wear of materials, John Wiley and Sons.

3. Fischer A (1988) Sliding wear of metallic materials at 25 and 550°C, Materials Research Society, Fall meeting.

4. Berns H, Fischer A, Kleff J (1993) Scratch tests on iron-, nickel- and cobalt-based alloys at elevated temperatures. Wear 162–164: 585–589.

5. Kayaba T, Hokkirigawa K, Kato K (1986) Analysis of the abrasive wear mechanism by successive observations of wear processes in a scanning electron microscope. Wear 110: 419–430.    

6. Perry A-J (1983) Scratch adhesion testing of hard coatings. Thin Solid Films 107: 167–180.

7. Buckley D-H, Rabinowicz (1986) Fundamentals of the wear of hard materials. 2nd International Conference Science Hard Materials, Rhodes.

8. Rodrigo A (2001) Analytical correlation of hardness and scratch adhesion for hard films. Surf Coat Tech 148: 8–17.

9. Xu X, Van der Zwaag S, Xu W (2016) The effect of martensite volume fraction on the scratch and abrasion resistance of a ferrite-martensite dual phase steel. Wear 348–349: 80–88.

10. Oliver W-C, Pharr G-M (1992) An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res 7: 1564–1583.    

11. Oliver W-C, Pharr G-M (2003) Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J Mater Res 19: 3–20.

12. Biwa S, Storakers B (1995) An analysis of fully plastic Brinell indentation. J Mech Phys Solids 43: 1303–1333.

13. Field J-S, Swain M-V (1995) Determining the mechanical properties of small volumes of materials from submicron spherical indentations. J Mater Res 10: 101–112.    

14. Pöhl F, Huth S, Theisen W (2014) Indentation of self-similar indenters: An FEM-assisted energy-based analysis. J Mech Phys Solids 66: 32–41.    

15. Lee J-M, Lee C-J, Lee K-H, et al. (2012) Effects of elastic-plastic properties of materials on residual indentation impressions in nano-indentation using sharp indenter. T Nonferr Metal Soc 22: 585–595.    

16. Bellemare S-C, Dao M, Suresh S (2008) Effects of mechanical properties and surface friction on elasto-plastic sliding contact. Mech Mater 40: 206–219.    

17. Fischer-Cripps A-C (2002) Nanoindentation, Springer.

18. Kobrick R-L, Klaus D-M, Street Jr KW (2011) Validation of proposed metrics for two‐body abrasion scratch test analysis standards. Wear 270: 11–12, 815–822.

19. Kobrick R-L, Klaus D-M, Street Jr K-W (2011) Standardization of a volumetric displacement measurement for two‐body abrasion scratch test data analysis. Wear 270: 9–10, 650–657.

20. Pöhl F, Schwarz S, Junker P, et al. (2015) Indentation and Scratch Testing-Experiment and Simulation. Proceedings of the 3rd International Conference on Stone and Concrete Machining (ICSCM), 319–336.

Copyright Info: © 2016, Fabian Pöhl, et al., licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution Licese (http://creativecommons.org/licenses/by/4.0)

Download full text in PDF

Export Citation

Article outline

Show full outline
Copyright © AIMS Press All Rights Reserved