Research article

Development of tensile fixture with corrugated structure sheet and estimation of tensile strength of glass fibre fabrics based single face corrugated structure sheet

  • Received: 17 December 2019 Accepted: 18 February 2020 Published: 25 February 2020
  • This work aims to reveal the tensile characteristics of Glass Fibre fabrics based single face corrugated Structure Sheet (GFSS) by developing a pressure-adjustable fixture in the machine producing direction of GFSS. In order to set the fixture quick-ready and stable, the effects of several set-up conditions on the tensile behavior of GFSS were investigated. As the set-up condition, a wavy aluminum block fitted to the surface trace, insertion of multiple flexible pins into wave holes, and double-sided tapes attached on the upper/lower surfaces were discussed by changing the number of pins N, and also a few of instant adhesives was dipped on the clamped/pressured zone of GFSS (the reinforced model). Through this study, the followings were revealed. To use multiple polystyrene pins and several pieces of double-sided tapes in the proposed fixture contributes to make the tensile line force stable (as the simple model: without any instant adhesives on the clamped zone). To perform the breakage of liner and wave layers in the area of the gauge span, the reinforced model is usable when choosing N > 1. Investigating the tensile response, the strength (peak maximum line force) and the elongation limit of the liner and wave layers were revealed, respectively. By dipping instant adhesives on the clamping zone when N > 6, the combination resistance of liner and wave braiding structure was actualized.

    Citation: Songtam Laosuwan, Shigeru Nagasawa, Kazuki Umemoto. Development of tensile fixture with corrugated structure sheet and estimation of tensile strength of glass fibre fabrics based single face corrugated structure sheet[J]. AIMS Materials Science, 2020, 7(1): 75-92. doi: 10.3934/matersci.2020.1.75

    Related Papers:

  • This work aims to reveal the tensile characteristics of Glass Fibre fabrics based single face corrugated Structure Sheet (GFSS) by developing a pressure-adjustable fixture in the machine producing direction of GFSS. In order to set the fixture quick-ready and stable, the effects of several set-up conditions on the tensile behavior of GFSS were investigated. As the set-up condition, a wavy aluminum block fitted to the surface trace, insertion of multiple flexible pins into wave holes, and double-sided tapes attached on the upper/lower surfaces were discussed by changing the number of pins N, and also a few of instant adhesives was dipped on the clamped/pressured zone of GFSS (the reinforced model). Through this study, the followings were revealed. To use multiple polystyrene pins and several pieces of double-sided tapes in the proposed fixture contributes to make the tensile line force stable (as the simple model: without any instant adhesives on the clamped zone). To perform the breakage of liner and wave layers in the area of the gauge span, the reinforced model is usable when choosing N > 1. Investigating the tensile response, the strength (peak maximum line force) and the elongation limit of the liner and wave layers were revealed, respectively. By dipping instant adhesives on the clamping zone when N > 6, the combination resistance of liner and wave braiding structure was actualized.


    加载中


    [1] Caproni G, Tagliferri V (1995) Damage development in drilling glass fibre reinforced plastics. Int J Mach Tool Manu Int 35: 817-829. doi: 10.1016/0890-6955(94)00055-O
    [2] Mehbudi P, Baghlani V, Akbari J, et al. (2013) Applying ultrasonic vibration to decrease drilling-induced delamination in GFRP laminates. Procedia CIRP 6: 577-582. doi: 10.1016/j.procir.2013.03.097
    [3] Loewenstein KL (1973) The Manufacturing Technology of Continuous Glass Fibres, 1st Ed., New York: Elsevier, 2-94.
    [4] Loewenstein KL (1975) The manufacture of continuous glass fibres. Platin Met Rev 19: 84-87.
    [5] Van Nostrand Reinhold (1982) Characterization of corrugated board, In: Lubin G, Handbook of Composite, 1st Ed., Boston: Springer, 145-149.
    [6] Steadman R (2002) Characterization of corrugated board, In: Mark RE, Borch J, Habeger C, Handbook of Physical Testing of Paper, 2 Eds., New York: CRC Press, 1: 571-574.
    [7] Dekker A (2013) Corrugated fiberboard packaging, In: Kirwan MJ, Handbook of Paper and Paperboard Packaging Technology, 2 Eds., New Jersey: Wiley-Blackwell, 313-321.
    [8] Jonson G (1999) Corrugated Board Packaging, 2 Eds., Leatherhead: Pira International, 145-159.
    [9] Kubo Corporation, Glass fibre based structural sheet. 2017. Available from: http://www.kubo-co.net/.
    [10] Matsushima S, Okuda T, Miyauchi O, et al. (1982) Strength of tensile deformation for corrugated fibre board. Jpn Tappi J 36: 377-387. doi: 10.2524/jtappij.36.377
    [11] Wahab N, Arafah A, Fukuzawa Y, et al. (2016) Estimation of corrugated cardboard strength using tensile test. Proceedings of Mechanical Engineering Research Day, 1-2.
    [12] Cox HL (1952) The elasticity and strength of paper and other fibrous materials. Br J Appl 3: 72-79. doi: 10.1088/0508-3443/3/3/302
    [13] Nagasawa S, Kudo H, Songtam L, et al. (2017) Tensile characteristics of glass fibre based single face board. Procedia Eng 207: 78-83. doi: 10.1016/j.proeng.2017.10.738
    [14] Niitobo Corporation, Mechanical properties of E-glass. 2019. Available from: https://www.nittobo.co.jp/business/glassfiber/about/composition.htm.
  • Reader Comments
  • © 2020 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索

Metrics

Article views(3210) PDF downloads(425) Cited by(1)

Article outline

Figures and Tables

Figures(16)  /  Tables(3)

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog