Export file:

Format

  • RIS(for EndNote,Reference Manager,ProCite)
  • BibTex
  • Text

Content

  • Citation Only
  • Citation and Abstract

Manipulating cement-steel interface by means of electric field: Experiment and potential applications

1 Formation Physics Department, SINTEF Petroleum Research, 7465 Trondheim, Norway
2 Drilling and Well Department, SINTEF Petroleum Research, 7465 Trondheim, Norway

Topical Section: Thin films, surfaces and interfaces

Good shear bonding and hydraulic bonding between cement and steel play a crucial role in well integrity of oil and gas wells. In this experimental study, we investigate the effect that constant electric field may have on the bonding at cement-steel interfaces. Constant voltage (18 V) was applied between two stainless-steel electrodes immersed into a cement slurry. It was found that bonding was significantly improved at the positive electrode, while it was significantly worse at the negative electrode. The effect was due to the negatively-charged cement particles being attracted to the positive electrode. The effect may potentially be used for manipulation and control of casing-cement and reinforcement-concrete bonding strengths in oil & gas and construction industries, respectively. Side-effects that might reduce the applicability of this technology, are gas production at both electrodes (and especially at the negative one) and significant corrosion at the positive electrode due to electrochemical reactions at metal surfaces. Poor bonding at the negative electrode may potentially be used for cleaning of cement equipment, such as cement pumps, pipes, tanks, and mixers used on the rigs to perform well cementing jobs in oil & gas industry.
  Figure/Table
  Supplementary
  Article Metrics

References

1. Nelson EB, Guillot D (2006) Well cementing: Schlumberger.

2. Kjøller C, Torsæter M, Lavrov A, et al. (2016) Novel experimental/numerical approach to evaluate the permeability of cement-caprock systems. Int J Greenhouse Gas Control 45: 86–93.    

3. Lavrov A, Cerasi P (2013) Numerical modeling of tensile thermal stresses in rock around a cased well caused by injection of a cold fluid. ARMA paper 13-306 presented at the 47th US Rock Mechanics/Geomechanics Symposium held in San Francisco, CA, USA.

4. Drever JI (1969) The separation of clay minerals by continuous particle electrophoresis. Am Mineral 54: 937–942.

5. Hoxha BB, Sullivan G, van Oort E, et al. (2016) Determining the zeta potential of intact shales via electrophoresis. SPE paper 180097 presented at the SPE Europec featured at the 78th EAGE Conference and Exhibition held in Vienne, Austria.

6. Nachbaur L, Mutin JC, Nonat A, et al. (2001) Dynamic mode rheology of cement and tricalcium silicate pastes from mixing to setting. Cement Concrete Res 31: 183–192.    

7. Roy S, Cooper GA (1993) Prevention of bit balling in shales - preliminary results. SPE Drill Completion 8: 195–200.    

8. Bourgoyne Jr. AT, Millheim KK, Chenevert ME, et al. (1991) Applied Drilling Engineering. Richardson: Society of Petroleum Engineers 502.

9. Lavrov A, Todorovic J, Torsæter M (2016) Impact of voids on mechanical stability of well cement. Energy Procedia 86: 401–410.    

10. Todorovic J, Gawel K, Lavrov A, et al. (2016) Integrity of downscaled well models subject to cooling. SPE paper 180025 presented at the SPE Bergen One Day Seminar held in Bergen, Norway.

Copyright Info: © 2016, Alexandre Lavrov, et al., licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution Licese (http://creativecommons.org/licenses/by/4.0)

Download full text in PDF

Export Citation

Article outline

Show full outline
Copyright © AIMS Press All Rights Reserved