Research article Topical Sections

Derivation, parameterization and validation of a creep deformation/rupture material constitutive model for SiC/SiC ceramic-matrix composites (CMCs)

  • Received: 31 March 2016 Accepted: 16 May 2016 Published: 18 May 2016
  • The present work deals with the development of material constitutive models for creep-deformation and creep-rupture of SiC/SiC ceramic-matrix composites (CMCs) under general three-dimensional stress states. The models derived are aimed for use in finite element analyses of the performance, durability and reliability of CMC turbine blades used in gas-turbine engines. Towards that end, one set of available experimental data pertaining to the effect of stress magnitude and temperature on the time-dependent creep deformation and rupture, available in the open literature, is used to derive and parameterize material constitutive models for creep-deformation and creep-rupture. The two models derived are validated by using additional experimental data, also available in the open literature. To enable the use of the newly-developed CMC creep-deformation and creep-rupture models within a structural finite-element framework, the models are implemented in a user-material subroutine which can be readily linked with a finite-element program/solver. In this way, the performance and reliability of CMC components used in high-temperature high-stress applications, such as those encountered in gas-turbine engines can be investigated computationally. Results of a preliminary finite-element analysis concerning the creep-deformation-induced contact between a gas-turbine engine blade and the shroud are presented and briefly discussed in the last portion of the paper. In this analysis, it is assumed that: (a) the blade is made of the SiC/SiC CMC; and (b) the creep-deformation behavior of the SiC/SiC CMC can be represented by the creep-deformation model developed in the present work.

    Citation: Grujicic Mica, Galgalikar Rohan, Ramaswami S., Snipes Jennifer S.. Derivation, parameterization and validation of a creep deformation/rupture material constitutive model for SiC/SiC ceramic-matrix composites (CMCs)[J]. AIMS Materials Science, 2016, 3(2): 591-619. doi: 10.3934/matersci.2016.2.591

    Related Papers:

  • The present work deals with the development of material constitutive models for creep-deformation and creep-rupture of SiC/SiC ceramic-matrix composites (CMCs) under general three-dimensional stress states. The models derived are aimed for use in finite element analyses of the performance, durability and reliability of CMC turbine blades used in gas-turbine engines. Towards that end, one set of available experimental data pertaining to the effect of stress magnitude and temperature on the time-dependent creep deformation and rupture, available in the open literature, is used to derive and parameterize material constitutive models for creep-deformation and creep-rupture. The two models derived are validated by using additional experimental data, also available in the open literature. To enable the use of the newly-developed CMC creep-deformation and creep-rupture models within a structural finite-element framework, the models are implemented in a user-material subroutine which can be readily linked with a finite-element program/solver. In this way, the performance and reliability of CMC components used in high-temperature high-stress applications, such as those encountered in gas-turbine engines can be investigated computationally. Results of a preliminary finite-element analysis concerning the creep-deformation-induced contact between a gas-turbine engine blade and the shroud are presented and briefly discussed in the last portion of the paper. In this analysis, it is assumed that: (a) the blade is made of the SiC/SiC CMC; and (b) the creep-deformation behavior of the SiC/SiC CMC can be represented by the creep-deformation model developed in the present work.


    加载中
    [1] Corman GS, Luthra KL (2006) Melt Infiltrated Ceramic Composites (HIPERCOMP®) For Gas Turbine Engine Applications, Continuous Fiber Ceramic Composites Program Phase II Final Report, Niskayuna, NY.GE Global Research, Technical Report DOE/CE/41000-2 .
    [2] C FM (2015) CFM International, LEAP Engine.Available from .
    [3] GE Aviation (2015) GE Successfully Tests World's First Rotating Ceramic Matrix Composite Material for Next-Gen Combat Engine.Available from .
    [4] Grujicic M, Galgalikar R, Snipes JS, et al. (2016) Creep-behavior-based material selection for a clamping spring of ceramic-matrix composite inner-shroud in utility and industrial gas-turbine engines.J Mater Des Appl .
    [5] Ashby MF, Abel CA (1995) Materials selection to resist creep.P Roy Soc A 351: 451-468.
    [6] Ashby MF, Shercliff HR, Cebon D (2007) Materials: Engineering, science, processing and design. Oxford, UK.Butterworth-Heinemann .
    [7] Morscher GN (2010) Tensile creep and rupture of 2-D woven SiC/SiC composites for high temperature applications.J Eur Ceram Soc 30: 2209-2221.
    [8] Morscher GN, Pujar VV (2006) Creep and stress-strain behavior after creep for SiC fiber reinforced, melt-infiltrated SiC matrix composites.J Am Ceram Soc 89: 1652-1658.
    [9] Morscher GN, Ojard G, Miller R, et al. (2008) Tensile creep and fatigue of Sylramic-iBN melt-infiltrated SiC matrix composites: Retained properties, damage development, and failure mechanisms.Compos Sci Technol 68: 3305-3313.
    [10] van Roode, Bhattacharya AK, Ferber MK, et al. (2010) Creep Resistance and Water Vapor Degradation of SiC/SiC Ceramic Matrix Composite Gas Turbine Hot Section Components, Proceedings of ASME Turbo Expo 2010.Power for Land, Sea and Air GT2010, June 14-18, 2010, Glasgow, UK .
    [11] Rospars C, Chermant JL, Ladevèze P (1998) On a first creep model for a 2D SiCf-SiC composite.Mater Sci Eng 250: 264-269.
    [12] Rugg KL, Tressler RE, Bakis CE, et al. (1999) Creep of SiC-SiC Microcomposites.J Eur Ceram Soc 19: 2285-2296.
    [13] Chermant JL, Boitier G, Darzens S, et al. (2002) The creep mechanism of ceramic matrix composites at low temperature and stress, by a material science approach.J Eur Ceram Soc 22: 2443-2460.
    [14] Grujicic M, Galgalikar R, Snipes JS, et al. (2016) Multi-length-scale material model for SiC/SiC ceramic-matrix composites (CMCs): inclusion of in-service environmental effects.J Mater Eng Perform 25: 199-219.
    [15] Casas L, Martinez-Esnaola JM (2003) Modelling the effect of oxidation on the creep behaviour of fibre-reinforced ceramic matrix composites.Acta Mater 51: 3745-3757.
    [16] Takeda M, Imai Y, Ichikawa H, et al. (1999) Thermal stability of SiC fiber prepared by an irradiation curing process.Compos Sci Technol 59: 793-799.
    [17] Grujicic M, Snipes JS, Galgalikar R, et al. (2015) Multi-length-scale derivation of the room-temperature material constitutive model for SiC/SiC ceramic-matrix composites (CMCs).J Mater: Des Appl .
    [18] Grujicic M, Chenna V, Galgalikar R, et al. (2014) Computational analysis of gear-box roller-bearing white-etch cracking: a multi-physics approach.Inter J Struct Integrity 5: 290-327.
    [19] Grujicic M, Ramaswami S, Yavari R, et al. (2016) Multi-physics computational analysis of white-etch cracking failure mode in wind-turbine gear-box bearings.J Mater Des Appl 230: 43-63.
    [20] Grujicic M, Galgalikar R, Ramaswami S, et al. (2015) Multi-Physics Modeling and Simulations of Reactive Melt Infiltration Process Used in Fabrication of Ceramic-Matrix Composites (CMCs).Multidiscip Mod Mater Struct 11: 43-74.
    [21] Grujicic M, Snipes JS, Yavari R, et al. (2015) Computational Investigation of Foreign Object Damage Sustained by Environmental Barrier Coatings (EBCs) and SiC/SiC Ceramic-Matrix Composites (CMCs).Multidiscip Mod Mater Struct 11: 238-272.
    [22] ABAQUS (2014) User Documentation, Dassault Systèmes.Dassault Systèmes .
    [23] Grujicic M, Ramaswami S, Snipes JS, et al. (2013) Computational investigation of roller-bearing premature-failure in horizontal-axis wind-turbine gearboxes.Solids Struct 2: 47-56.
    [24] Grujicic M, Chenna V, Galgalikar R, et al. (2014) Wind-turbine gear-box roller-bearing premature-failure caused by grain-boundary hydrogen embrittlement: A multi-physics computational investigation.J Mater Eng Perform 23: 3984-4001.
    [25] Grujicic M, Chenna V, Yavari R, et al. (2015) Multi-length scale computational analysis of roller-bearing premature failure in horizontal-axis wind-turbine gear-boxes.Int J Struct Integ 5: 40-72.
  • Reader Comments
  • © 2016 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索

Metrics

Article views(7064) PDF downloads(1609) Cited by(1)

Article outline

Figures and Tables

Figures(10)  /  Tables(1)

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog