Search Advanced

AIMS Electronics and Electrical Engineering

2020, Volume 4, Issue 4: 369-388. doi: 10.3934/ElectrEng.2020.4.369
Previous Article Next Article
Research article

An advanced semiconductor material selection for switching devices in electric vehicles using three multiple attribute decision making methods

  • 1.
    Department of Electrical Engineering, Sardar Vallabhbhai National Institute of Technology, Surat, India
  • 2.
    Department of Electrical Engineering, Visvesvaraya National Institute of Technology, Nagpur, India
  • Received: 26 July 2020 Accepted: 09 December 2020 Published: 30 December 2020

  • Electric Vehicle (EV) has emerged as a solution for the growing concerns on pollution and depleting oil resources all over the world. The performance and efficiency of an EV mainly depends on the power electronic switching devices used in it which, in turn depends on the properties of materials used in its fabrication. Traditional semiconductor material like Silicon has been widely used for the fabrication of these switches. However, improvised material technology and incessant demand for better performance has triggered the use of wide band-gap (WBG) semiconductors in switching devices. This paper aims to compare a few WBG semiconductors with traditional semiconductors based on their material properties. Three decision making methods has been used for comparison and the possibly best material for fabrication of switching devices has been chosen based on their rankings achieved. Adoption of the suggested material can improve the performance and efficiency of EV's theoretically.

    Citation: Shimin V V, Varsha A Shah, Makarand M Lokhande. An advanced semiconductor material selection for switching devices in electric vehicles using three multiple attribute decision making methods[J]. AIMS Electronics and Electrical Engineering, 2020, 4(4): 369-388. doi: 10.3934/ElectrEng.2020.4.369

    Related Papers:

  • Electric Vehicle (EV) has emerged as a solution for the growing concerns on pollution and depleting oil resources all over the world. The performance and efficiency of an EV mainly depends on the power electronic switching devices used in it which, in turn depends on the properties of materials used in its fabrication. Traditional semiconductor material like Silicon has been widely used for the fabrication of these switches. However, improvised material technology and incessant demand for better performance has triggered the use of wide band-gap (WBG) semiconductors in switching devices. This paper aims to compare a few WBG semiconductors with traditional semiconductors based on their material properties. Three decision making methods has been used for comparison and the possibly best material for fabrication of switching devices has been chosen based on their rankings achieved. Adoption of the suggested material can improve the performance and efficiency of EV's theoretically.


    加载中


    [1] Chan CC, Chau KT (1996) An overview of electric vehicles-challenges and opportunities. Proceedings of the 1996 IEEE IECON 22nd International Conference on Industrial Electronics, Control, and Instrumentation 1: 1–6.
    [2] Shen ZJ, Omura I (2007) Power semiconductor devices for hybrid, electric, and fuel cell vehicles. Proceedings of the IEEE 95: 778–789.
    [3] Jain H, Rajawat S, Agrawal P (2008) Comparision of wide band gap semiconductors for power electronics applications. In International Conference on Recent Advances in Microwave Theory and Applications, 878–881.
    [4] Tolbert LM, Ozpineci B, Islam SK, et al. (2002) Impact of sic power electronic devices for hybrid electric vehicles. SAE Transactions, 765–771.
    [5] Hudgins JL, Simin GS, Santi E, et al. (2003) An assessment of wide bandgap semiconductors for power devices. IEEE Transactions on Power Electronics 18: 907–914.
    [6] Holmes KC, Davidson JL, Kang WP, et al. (2001) Diamond microelectromechanical sensors for pressure and acceleration sensing. Microelectromechanical Systems Conference, 45–49.
    [7] Wisitsora-At A, Kang WP, Davidson JL, et al. (2003) Diamond field-emission triode with low gate turn-on voltage and high gain. Journal of Vacuum Science & Technology B 21: 614–617.
    [8] Wondrak W (1999) Physical limits and lifetime limitations of semiconductor devices at high temperatures. Microelectronics Reliability 39: 1113–1120.
    [9] Millán J, Godignon P, Pérez-Tomás A (2012) Wide band gap semiconductor devices for power electronics. Automatika–Journal for Control, Measurement, Electronics, Computing and Communications 53: 107–116.
    [10] Ozpineci B, Tolbert LM (2004) Comparison of wide-bandgap semiconductors for power electronics applications. United States. Department of Energy.
    [11] Kirschman RK (1999) High temperature electronics. IEEE Press New York, NY.
    [12] Bhatnagar M, Baliga BJ (1993) Comparison of 6h-sic, 3c-sic, and si for power devices. IEEE Transactions on Electron Devices 40: 645–655.
    [13] Shenai K, Scott RS, Baliga BJ (1989) Optimum semiconductors for high-power electronics. IEEE Transactions on Electron Devices 36: 1811–1823.
    [14] Willander M, Friesel M, Wahab QU, et al. (2006) Silicon carbide and diamond for high temperature device applications. Journal of Materials Science: Materials in Electronics 17: 1–25.
    [15] Willardson RK, Weber ER (1998) SiC materials and devices, volume 52, Academic Press.
    [16] Dorf RC (1997) The electrical engineering handbook. CRC press.
    [17] Harris R (1998) Introduction to decision making.
    [18] Baker D, Bridges D, Hunter R, et al. (2002) Guidebook to decision making methods. department of energy, USA.
    [19] Tzeng GH, Huang JJ (2011) Multiple attribute decision making: methods and applications. CRC press.
    [20] Rao RV (2007) Decision making in the manufacturing environment: using graph theory and fuzzy multiple attribute decision making methods. Springer Science & Business Media.
    [21] Vinogradova I (2019) Multi-attribute decision-making methods as a part of mathematical optimization. Mathematics 7: 915.
    [22] Grummel BJ (2008) High Temperature Packaging for Wide Bandgap Semiconductor Devices. PhD thesis, University of Central Florida Orlando, Florida.
    [23] Saaty TL (1988) What is the analytic hierarchy process? Springer.
    [24] Hwang CL, Yoon KP (1981) Multiple decision attribute making: Methods and applications. Springer.
    [25] Brans JP, Vincke P (1985) Note—a preference ranking organisation method: (the promethee method for multiple criteria decision-making). Management science 31: 647–656.
    [26] Brans JP, Vincke P, Mareschal B (1986) How to select and how to rank projects: The promethee method. Eur J Oper Res 24: 228–238.
    [27] Brans JP, Mareschal B (2005) Promethee methods. Multiple criteria decision analysis, 163–186. Springer.
  • Reader Comments
  • © 2020 the Author(s), licensee AIMS Press. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0)
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索
AIMS Electronics and Electrical Engineering
2.6

Metrics

Article views(1960) PDF downloads(142) Cited by(2)

Preview PDF
Download XML
Export Citation
Article outline

Figures and Tables

Figures(1)  /  Tables(21)

Other Articles By Authors

Related pages

Tools

/

DownLoad:  Full-Size Img  PowerPoint
Return
Return

Catalog